Mã lỗi Ricoh D132 MP7502
Code:
Tất cả lỗi (258)
101
120
121
141
142
144
161-01
161-02
161-02
161-03
165
181
182
185
186
187
188
189
195
202
203
204
205
220
221
230
231
240
270
300
305-00
306-00
307-00
320-01
324-01
360-01
360-11
361-00
362-00
370-0
370-11
375-00
376-00
377-00
378-00
380-01
380-11
380-21
380-31
380-41
380-51
396-01
410-00
440-01
440-02
495-00
496-00
501
502
503
504
510
515-00
516-00
530-00
540-01
540-02
540-03
540-04
541
542-001
542-002
542-003
543
544
545
547-01
547-02
547-03
551
552-01
552-02
552-03
553
555
557
559
569
590-00
620-01
620-2
621-01
621-02
623
626-01
626-02
632
633
634
635
636-01
636-02
636-11
637-01
637-02
640
641
650-01
650-04
650-05
650-13
650-14
651-01
652
653
670
671
672
700-01
700-02
720-01
720-24
720-25
720-30
720-41
720-42
720-43
720-44
720-52
720-53
720-55
720-57
720-60
720-61
720-70
720-71
720-72
720-73
720-74
720-75
720-80
720-81
720-87
722-01
722-10
722-24
722-25
722-30
722-33
722-35
722-36
722-37
722-39
722-40
722-41
722-42
722-43
722-44
722-70
722-71
722-72
722-74
722-75
722-80
722-81
722-83
724-71
725-01
725-12
725-13
725-14
725-30
725-31
725-32
725-33
725-34
725-35
725-36
725-37
725-38
725-41
725-71
725-72
725-73
725-74
740-10
783-3
783-4
816
817
819
820
821
822
823
824
829
833
834
838
840
841
842
850
851
853
854
855
857
858
859
860
861
862
863
864
865
866
867
868
870
872
873
874
875
876
877
878
880
881
889
900
901
910
911
912
913
914
915
919
920
921
925
953
954
955
964
965
984
985
986
990
991
992
994
995
997
998
Description: Exposure Lamp Error At trigger on, the lamp was not detected on.
Causes: • SBU board defective • SIOB board defective • IPU board defective • BCU board defective • Exposure lamp defective • Lamp stabilizer defective • Lamp stabilizer harness damaged, disconnected • Standard white plate dirty, disconnected or has condensation • DF white belt dirty • DF glass dirty or has condensation • Scanner mirror dirty, out of position or has condensation • Lens dirty, out of position
Description: Scanner home position error 1 The scanner HP sensor does not detect the OFF condition during initialization or copying.
Causes: • BCU, SIOB defective • Scanner motor defective • Scanner HP sensor defective. • Harness between BCU, SIOB, scanner motor disconnected. • Harness between scanner HP sensor and BCU disconnected. • Scanner wire, timing belt, pulley, or carriage installed incorrectly.
Description: Scanner home position error 2 The scanner HP sensor does not detect the ON condition during initialization or copying.
Causes: • BCU, SIOB defective • Scanner motor defective • Scanner HP sensor defective • Harness between BCU, SIOB, scanner motor disconnected • Harness between scanner HP sensor and BCU disconnected • Scanner wire, timing belt, pulley or carriage installed incorrectly.
Description: Black level detection error The black level cannot be adjusted within the target during auto gain control.
Causes: • Harness between SBU – SIOB is disconnected. • Harness between SIOB – BCU is disconnected. • Defective SBU • Defective BCU
Description: White level detection error The white level cannot be adjusted to the second target level within the target during auto gain control.
Causes: • Dirty exposure lamp or optics section • SBU board defective • SIOB defective • IPU board defective • BCU board defective • Harnesses are disconnected. • Exposure lamp defective • Lamp stabilizer defective • Scanner motor defective
Description: SBU transmission error After the SBU switches on, the BCU detects one of the following conditions on the SBU: • 1 s after power on, the SYDO signal does not go high, even after 1 retry. • 1 s after power on, the SYDO signal goes high, but the SBU ID could not be read after 3 attempts.
Causes: • SBU defective • SIOB defective • BCU defective • Harness between the SBU - SIOB is disconnected • Harness between the SIOB - BCU is disconnected • Harness between the SIOB – PSU is disconnected
Description: IPU error The error result of self-diagnostic by the ASIC on the BICU is detected.
Causes: • Defective BICU • Defective connection between BICU and SBU
Description: IPU error (LSYNC abnormal) The error result of self-diagnostic by the ASIC on the BICU is detected.
Causes: • Defective BICU • Defective connection between BICU and SBU