Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh G178 Aficio Pro C900 AG-P1 — Trang 34/85

Code: 534-001, 534-002

Description: -001 B Fan alarm 3: A3 LCT rear air assist fan 3 -002 B Fan alarm 3: A3 LCT rear air assist fan 3 The machine detects a fan alarm signal from front or rear air assist fan 3 for 0.7 second after the paper exit motor has started rotating for 1 second.
Causes: • An obstruction has stopped front or rear air assist fan 3. • Harness disconnected
Remedy: 1. Check the harness connection to front or rear air assist fan 3. 2. Replace front or rear air assist fan 3.

Code: 535-001, 535-002

Description: -001 B Fan alarm 3: A3 LCT rear air assist fan 4 -002 B Fan alarm 3: A3 LCT rear air assist fan 4 The machine detects a fan alarm signal from front or rear air assist fan 4 for 0.7 second after the paper exit motor has started rotating for 1 second.
Causes: • An obstruction has stopped front or rear air assist fan 4. • Harness disconnected
Remedy: 1. Check the harness connection to front or rear air assist fan 4. 2. Replace front or rear air assist fan 4.

Code: 541

Description: Heating roller thermopile error The temperature measured by the thermopile does not reach 0°C for 10 seconds.
Causes: • Loose connection of the thermopile • Defective thermopile
Remedy: 1. Do SP5810 to cancel the SC fusing code. 2. Check if the thermopile is firmly connected. 3. Replace the thermopile.

Code: 542

Description: Heating roller warm-up error 1 • The center temperature of the heating roller does not reach the ready temperature for 830 seconds after the heating lamp on. • The center temperature of the heating roller does not reach 100°C for 400 seconds after the heating roller lamp on.
Causes: Dirty or defective thermopile
Remedy: 1. Do SP5810 to cancel the SC fusing code. 2. Check if the thermopile is firmly connected. 3. Replace the thermopile.

Code: 543

Description: Heating roller overheat 1 (software error) The detected fusing temperature (center) stays at 225°C for 10 seconds.
Causes: • TRIAC short, AC drive board defective • Defective IOB 2 • Defective BCU • Related SC code: SC 553, SC563
Remedy: 1. Do SP5810 to cancel the SC fusing code. 2. Replace the AC drive board. 3. Replace the IOB 2. 4. Replace the BCU.

Code: 544

Description: Heating roller thermopile (center) error 3 The thermopile detected a temperature over 260°C.
Causes: • TRIAC short, AC drive board defective • Defective IOB 2 • Defective BCU • Related SC code: SC 553, SC563
Remedy: 1. Do SP5810 to cancel the SC fusing code. 2. Replace the AC drive board. 3. Replace the IOB 2. 4. Replace the BCU.

Code: 545

Description: Heating roller fusing lamp on error After fusing belt reached warm-up temperature, the heating roller fusing lamp remained on for 360 sec. while the hot roller was not rotating.
Causes: • Thermopile damaged, or out of position • Fusing lamp disconnected, broken
Remedy: 1. Do SP5810 to cancel the SC fusing code. 2. Replace the thermopile.

Code: 547

Description: Zero cross error • The zero cross signal is detected once in the three zero cross signal detections even though the heater relay is off when turning on the main power. • The detection error occurs twice or more in the 10 zero cross signal detections. This error is defined when the detected zero cross signal is less than 44.
Causes: • Defective fusing relay • Defective fusing relay circuit • Shorted +24V fuse on the PSU • Unstable power supply • Defective breaker or breaker off • Defective FIB (+6VGINT off) • Defective AC drive board (Defective power relay) • Defective IOB 2
Remedy: 1. Check the power supply source. 2. Make sure that the breaker is turned on. 3. Replace the breaker if the breaker is not turned on. 4. Replace the FIB if +6VGINT (CN337-1 on IOB 2) is OFF. 5. Replace the AC drive board. 6. Replace the IOB 2. 7. Replace the +24V fuse on the PSU. 8. Replace the PSU
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie