Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh M124 SPC830DN

Code: 195

Description: Serial Number Mismatch
Serial numbers (11 digits) do not match.
Causes: Checking if the serial number matches
Remedy: Input the serial number.

Code: 202

Description: Polygon motor error 1: ON timeout
The polygon mirror motor does not reach the targeted operating speed within the specified time after turning on or changing speed.
Causes: Defective or disconnected harness to polygon motor driver board. Defective polygon motor driver board. Defective polygon motor. The polygon motor drive pulse is not released correctly. The XSCRDY signal cannot be monitored.
Remedy: • Turn the main power switch off and then back on. • Replace the laser optics housing unit. • Replace the I/F harness. • Replace the BCU.

Code: 203

Description: Polygon motor error 2: OFF timeout
The polygon mirror motor does leave the READY status within 3 seconds after the polygon motor switches off.
Causes: Disconnected or defective harness to polygon motor driver board. Defective polygon motor driver board. Defective polygon motor. The polygon motor drive pulse is not released correctly. The XSCRDY signal cannot be monitored.
Remedy: • Turn the main power switch off and on. • Replace the laser optics housing unit. • Replace the I/F harness. • Replace the BCU.

Code: 204

Description: Polygon motor error 3: XSCRDY signal error
The motor's unlocked status is detected by monitoring of the polygon motor ready signal during writing (during the polygon motor's steady rotation).
Causes: Disconnected or defective harness to polygon motor driver board. Defective polygon motor. Defective polygon motor driver board.
Remedy: • Turn the main power switch off and on. • Replace the laser optics housing unit. • Replace the I/F harness. • Replace the BCU.

Code: 210-01

Description: Laser synchronizing detection error: end position [K]
The laser synchronizing detection signal for the end position of LDB [K], [C], [M], [Y] is not detected for 200 ms after the LDB unit turned on when detecting the main scan magnification.
Causes: Disconnected or defective I/F harness to laser synchronizing detection unit. Defective laser synchronizing detection board. The laser fails to reach the photo detector. Defective GAVD. Defective LD board or driver. Defective BCU.
Remedy: • Turn the main power switch off and then back on. • Replace the laser optics housing unit. • Replace the harness. • Replace the BCU.

Code: 210-02

Description: Laser synchronizing detection error: end position [C]
The laser synchronizing detection signal for the end position of LDB [K], [C], [M], [Y] is not detected for 200 ms after the LDB unit turned on when detecting the main scan magnification.
Causes: Disconnected or defective I/F harness to laser synchronizing detection unit. Defective laser synchronizing detection board. The laser fails to reach the photo detector. Defective GAVD. Defective LD board or driver. Defective BCU.
Remedy: • Turn the main power switch off and then back on. • Replace the laser optics housing unit. • Replace the harness. • Replace the BCU.

Code: 210-03

Description: Laser synchronizing detection error: end position [M]
The laser synchronizing detection signal for the end position of LDB [K], [C], [M], [Y] is not detected for 200 ms after the LDB unit turned on when detecting the main scan magnification.
Causes: Disconnected or defective I/F harness to laser synchronizing detection unit. Defective laser synchronizing detection board. The laser fails to reach the photo detector. Defective GAVD. Defective LD board or driver. Defective BCU.
Remedy: • Turn the main power switch off and then back on. • Replace the laser optics housing unit. • Replace the harness. • Replace the BCU.

Code: 210-04

Description: Laser synchronizing detection error: end position [Y]
The laser synchronizing detection signal for the end position of LDB [K], [C], [M], [Y] is not detected for 200 ms after the LDB unit turned on when detecting the main scan magnification.
Causes: Disconnected or defective I/F harness to laser synchronizing detection unit. Defective laser synchronizing detection board. The laser fails to reach the photo detector. Defective GAVD. Defective LD board or driver. Defective BCU.
Remedy: • Turn the main power switch off and then back on. • Replace the laser optics housing unit. • Replace the harness. • Replace the BCU.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie