Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh M172 SP3600SF Gim-MF1a — Trang 4/14

Code: SC545-00

Description: Fusing (Center) lamp stays ON
Causes: The thermistor (center) has not detected the target temperature, even after the fusing lamp stays ON for more than 30 seconds after reloading. • Deformed or floating thermistor • Broken fusing lamp wire • The overtemperature prevention mechanism started working
Remedy: • Clear the SP: fusing SC. • Replace the fusing thermistor. • Replace the fusing (Center) lamp.

Code: SC547-01

Description: Zero-crossing error (adhered relay contact)
Causes: When the fusing relay is in an OFF state, a "zero-crossing interrupt request" occurs in 50 ms. Damaged fusing relay (adhered contact)
Remedy: • Turn the main power OFF and then ON. • Replace the harness. • Replace the PC board. • Replace the PSU.

Code: SC547-02

Description: Zero-crossing error (bad relay contact)
Causes: If a "zero-crossing interrupt request" does not occur when the fusing relay is in an ON state, an error results. - Damaged fusing relay (open contact) - Failed fusing relay drive circuit - PSU fuse (24VS) blown
Remedy: • Turn the main power OFF and then ON. • Replace the harness. • Replace the Engine Board. • Replace the PSU. • Replace the fuse.

Code: SC547-03

Description: Zero-crossing error (low frequency error)
Causes: The number of zero-crossing interrupts does not reach a certain value in 500 ms. The frequency of the commercial power supply is unstable.
Remedy: • Turn the main power OFF and then ON. • Check the commercial power supply. • Replace the harness. • Replace the Engine Board. • Replace the PSU.

Code: SC551-00

Description: Broken fusing (End) thermistor wire
Causes: At least ten times, the temperature is detected to stay at -20 deg C or less for 5 seconds. • Broken thermistor wire • Bad connector contact
Remedy: • Clear the SP: fusing SC. • Check the connector connection. • Replace the fusing (End) thermistor.

Code: SC553-01

Description: Fusing (End) thermistor high-temperature detected (software)
Causes: In a condition of 235 degrees C or higher temperature, the temperature has increased more than 10 degrees C per 1 second, the heater has continuously reached 100% (maximum) duty, and the center thermistor has detected the failure to reach the target temperature by 11 degrees C. • Shorted triac • Failed Engine Board
Remedy: • Clear the SP: fusing SC. • Replace the PSU. • Replace the Engine Board.

Code: SC553-02

Description: Fusing (End) thermistor high-temperature detected (software)
Causes: The temperature is detected to stay at 245 deg C or higher for one second. • Shorted triac • Failed Engine Board
Remedy: • Clear the SP: fusing SC. • Replace the PSU. • Replace the Engine Board.

Code: SC554-00

Description: Fusing (End) thermistor high-temperature detected (hardware)
Causes: The hardware high-temperature error sensor flag is detected. • Damaged triac (shorted) • Failed engine control board • Failed fusing thermopile • Failed fusing thermistor • Abnormal fusing control software behavior • The PWM signal is continuously supplied from the IH inverter (due to a software or temperature sensor error).
Remedy: • Clear the SP: fusing SC. • Replace the PSU. • Replace the Engine Board. • Replace the fusing thermopile. • Replace the Fusing Unit.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie