Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Sharp MX6500N — Trang 19/26

Code: H7-14

Description: Low temperature detection during the temperature control reset operation after stopping the alarm in a JOB (HL_EX1)
Causes: When the alarm is stopped, the set temperature is not reached within the specified time. * Alarm stop: When the fusing temperature falls below the specified level in a print JOB, printing is interrupted temporarily and the temperature is reset.
Remedy: Case 1 Cause Connector and harness connection trouble Check and remedy Check connection of the connector and the harness. Case 2 Cause Thermistor trouble, thermostat trouble, heater lamp trouble, PCU PWB trouble, AC power source trouble, interlock switch trouble Check and remedy Use SIM 5-2 to check lighting of the heater lamp. Check conduction of the thermostat. Replace the heater lamp, the PCU PWB, and the AC PWB.

Code: L1-00

Description: Mirror feed trouble
Causes: Mirror unit trouble, mirror wire disengagement
Remedy: Use SIM1-1 to check the mirror operation.

Code: L3-00

Description: Mirror return trouble
Causes: Mirror unit trouble, mirror wire disengagement
Remedy: Use SIM1-1 to check the mirror operation.

Code: L4-02

Description: Paper feed motor lock trouble
Causes: Paper feed motor trouble, harness connection trouble between PCU PWB and paper feed motor, control circuit trouble
Remedy: Use SIM6-1 to check the paper feed motor operation. Check the harness and the connector between the PCU PWB and the paper feed motor.

Code: L4-03

Description: Fusing motor lock trouble
Causes: The motor lock signal is detected during rotation of the fusing motor.
Remedy: Case 1 Cause Harness connection trouble between the PCU PWB and the fusing motor. Check and remedy Check the harness and the connector between the PCU PWB and the fusing motor. Case 2 Cause Fusing motor trouble, control circuit trouble Check and remedy Use SIM6-1 to check the operation of the fusing motor.

Code: L4-04

Description: Developing motor trouble (BK)
Causes: The motor lock signal is detected during rotation of the developing motor.
Remedy: Case 1 Cause Harness connection trouble between the PCU PWB and the developing motor. Check and remedy Check the harness and the connector between the PCU PWB and the developing motor. Case 2 Cause Developing motor trouble, control circuit trouble Check and remedy Use SIM25-1 to check the operation of the developing motor.

Code: L4-05

Description: Developing motor trouble (CL)
Causes: The motor lock signal is detected during rotation of the developing motor.
Remedy: Case 1 Cause Harness connection trouble between the PCU PWB and the developing motor. Check and remedy Check the harness and the connector between the PCU PWB and the developing motor. Case 2 Cause Developing motor trouble, control circuit trouble Check and remedy Use SIM25-1 to check the operation of the developing motor.

Code: L4-06

Description: Transfer belt separation position sensor trouble
Causes: When separating the primary transfer belt unit, change in the separation position sensor characteristics is not detected within the specified time.
Remedy: Case 1 Cause Harness connection trouble between the PCU PWB and the separation position sensor Check and remedy Check the harness between the PCU PWB and the separation position sensor. Case 2 Cause The belt position sensor is not interrupted or it is always interrupted. Belt separation clutch operation trouble Check and remedy Use SIM6-3 to check the belt separation operation. Check to insure that the sensor is interrupted from lighting when the belt is separated. Case 3 Cause The primary transfer belt unit is not installed. Check and remedy Install the primary transfer belt unit.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie