Remedy: 1 Turn the printer off, and remove the rear cover. Check the connector JMIRR1 for proper connection to the system card, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. Go to step 2. 2 Replace the printhead. Does the error clear? Problem solved. Replace the system card.
Description: An error has occurred in the cyan channel of the printhead.
Remedy: 1 Is the front access door completely closed? Go to step 2. Properly close the door. 2 Turn the printer off, and remove the rear cover. Check the connector JINT1 (5 V interlock switch cable) for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the front access door 5 V interlock switch. Go to step 3. 3 Turn the printer power on, and check for 5 V dc between JINT1 pin (red wire) and ground. Is voltage present? Replace the front access door 5 V interlock switch. Go to step 4. 4 Replace the printhead. Does the error clear? Problem solved. Replace the system card.
Description: An error has occurred in the magenta channel of the printhead.
Remedy: 1 Is the front access door completely closed? Go to step 2. Properly close the door. 2 Turn the printer off, and remove the rear cover. Check the connector JINT1 (5 V interlock switch cable) for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the front access door 5 V interlock switch. Go to step 3. 3 Turn the printer power on, and check for 5 V dc between JINT1 pin (red wire) and ground. Is voltage present? Replace the front access door 5 V interlock switch. Go to step 4. 4 Replace the printhead. Does the error clear? Problem solved. Replace the system card.
Description: An error has occurred in the yellow channel of the printhead.
Remedy: 1 Is the front access door completely closed? Go to step 2. Properly close the door. 2 Turn the printer off, and remove the rear cover. Check the connector JINT1 (5 V interlock switch cable) for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the front access door 5 V interlock switch. Go to step 3. 3 Turn the printer power on, and check for 5 V dc between JINT1 pin (red wire) and ground. Is voltage present? Replace the front access door 5 V interlock switch. Go to step 4. 4 Replace the printhead. Does the error clear? Problem solved. Replace the system card.
Description: An error has occurred in the black channel of the printhead.
Remedy: 1 Is the front access door completely closed? Go to step 2. Properly close the door. 2 Turn the printer off, and remove the rear cover. Check the connector JINT1 (5 V interlock switch cable) for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the front access door 5 V interlock switch. Go to step 3. 3 Turn the printer power on, and check for 5 V dc between JINT1 pin (red wire) and ground. Is voltage present? Replace the front access door 5 V interlock switch. Go to step 4. 4 Replace the printhead. Does the error clear? Problem solved. Replace the system card.
Remedy: 1 Check the input voltage switch on the back of the low voltage power supply (LVPS). Is the voltage level (115/230) properly set? Go to step 2. Set the switch for proper country voltage. 2 Remove the fuser, and check the camshaft follower on the right side. If the camshaft follower (A) is above the crescent-shaped groove, it needs to be pressed down into the proper location. Is the camshaft follower on the right side properly placed in the groove? Go to step 3. Press the camshaft follower into the groove. 3 Turn the printer off, and remove the rear cover. Check the connector JFUSER1 for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the fuser cable. Go to step 4. 4 Check the connector JLVPS1 for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the LVPS cable. Go to step 5. 5 Remove the fuser. Check the AC and DC autoconnects on both the fuser and the printer for damage. Are the connectors damaged? Replace the appropriate cable. Go to step 6. 6 Check for the following continuity between the DC autoconnect and FUSER1. Is continuity present? Go to step 7. Replace the DC fuser cable. 7 Check for continuity between the following pins of the AC autoconnect and the pins of the connector that connects to the LVPS. Is continuity present? Go to step 8. Replace the AC fuser cable. 8 Replace the fuser. Does the error clear? Problem solved. Replace the system card.
Remedy: Remove and reseat the fuser. 1 Check the input voltage switch on the back of the low voltage power supply (LVPS). Is the voltage level (115/230) properly set? Go to step 2. Set the switch for proper the country voltage. 2 Turn the printer off, and remove the rear cover. Check the connector JFUSER1 for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the fuser cable. Go to step 3. 3 Check the connector JLVPS1 for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the LVPS. Go to step 4. 4 Replace the fuser. Does the error clear? Problem solved. Replace the system card.
Remedy: 1 Check the input voltage switch on the back of the low voltage power supply (LVPS). Is the voltage level (115/230) properly set? Go to step 2. Set the switch for the proper country voltage. 2 Turn the printer off, and remove the rear cover. Check the connector JFUSER1 for proper connection to the system card, the cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the fuser cable. Go to step 3. 3 Remove the fuser. Check the AC and DC autoconnects on both the fuser and the printer for damage. Are the connectors damaged? Go to step 4. Replace the appropriate cable. 4 Check for the following continuity between DC autoconnect and JFUSER1. Is continuity present? Go to step 5. Replace the DC fuser cable. 5 Check for continuity between the following pins of the AC autoconnect and the pins of the connector that connects to the LVPS. Is continuity present? Go to step 6. Replace the AC fuser cable. 6 Reinstall the fuser. Does the error clear? Problem solved. Go to step 7. 7 Replace the fuser. Does the error clear? Problem solved. Replace the system card.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.