Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 2307 — Trang 4/8

Code: E030

Description: Power-ON jam: The paper is remaining on the paper transport path when power is turned ON.
Causes: Sensor. MAIN board
Remedy: 1 Open the cover of the unit/ area whose picture is blinking on the control panel. Is there any paper on the transport path? (Refer to the following table.) Yes Remove the paper. No 2 2 Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table.) Yes 3 No • Check if the connector of the sensor is disconnected. • Check if any of the connectors on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the sensor 3 MAIN board • Replace the MAIN board.
Registration area Right cover Registration sensor 03-[A]/[A] Exit area Right cover Exit sensor 03-[A]/[B] ADU Right cover ADU paper path sensor 03-[1]/[C] PFU PFU side cover PFU drawer feed sensor 03-[4]/[A] PFP PFP side cover PFP upper drawer feed sensor 03-[1]/[E] PFP upper lower feed sensor 03-[2]/[C]

Code: E061

Description: Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment.
Causes:
Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer.

Code: E062

Description: Incorrect paper size setting for PFU drawer: The size of paper in the 2nd drawer differs from size setting of the equipment.
Causes:
Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer.

Code: E063

Description: Incorrect paper size setting for PFP upper drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.
Causes:
Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer.

Code: E064

Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
Causes:
Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer.

Code: E065

Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.
Causes:
Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer.

Code: E090

Description: Time out jam: Image data to be printed cannot be prepared.
Causes: ADU clutch MAIN board Rollers in the ADU
Remedy: dure Check item Result Measure Next Step 1 Open the ADU. Is there any paper in front of the registration sensor? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: 03-[A]/ [A]) Yes 3 No • Check if the connector of the registration sensor is disconnected. • Check if the connector CN22 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the 1st registration sensor. • Replace the MAIN board. 3 Is the ADU clutch working? (Perform the output check in the test mode: 03-222) Yes 4 No • Check if the connector of the ADU clutch is disconnected. • Check if the connector CN17 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the ADU clutch. • Replace the MAIN board. 4 Rollers in the ADU • Check the rollers in the ADU. Replace them if they are worn out.

Code: E110

Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
Causes: ADU clutch MAIN board Rollers in the ADU
Remedy: 1 Open the ADU. Is there any paper in front of the registration sensor? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: 03-[A]/ [A]) Yes 3 No • Check if the connector of the registration sensor is disconnected. • Check if the connector CN22 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the 1st registration sensor. • Replace the MAIN board. 3 Is the ADU clutch working? (Perform the output check in the test mode: 03-222) Yes 4 No • Check if the connector of the ADU clutch is disconnected. • Check if the connector CN17 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the ADU clutch. • Replace the MAIN board. 4 Rollers in the ADU • Check the rollers in the ADU. Replace them if they are worn out.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie