• Code: CB95
• Description: Saddle Stitch Finisher stacker motor abnormality MJ-1110. The [CB95] error also occurs when the error [EF16] has occurred consecutively for 3 times.
• Causes: Stacker motor Saddle control PC board
• Remedy: Stacker carrier • Is there any mechanical problem when the stacker carrier is moved? Stacker motor (M14) • Motor check • Connector check (CN8) • Harness check Saddle control PC board (SDL) • Connector check (CN8) • Board check

• Code: CBA0
• Description: Front saddle stapler home position error MJ-1110. The detection of the home position of the stapler unit ends abnormally
• Causes: Front saddle stapler clinch unit Saddle control PC board (SDL)
• Remedy: Front saddle stapler clinch unit • Harness check • Connector check Saddle control PC board (SDL) • Connector check (CN2) • Board check

• Code: CBB0
• Description: Rear saddle stapler home position error MJ-1110. The detection of the home position of the stapler unit ends abnormally.
• Causes: Rear saddle stapler clinch unit Saddle control PC board (SDL)
• Remedy: Rear saddle stapler clinch unit Harness check Saddle control PC board (SDL) • Connector check (CN1) • Board check

• Code: CBC0
• Description: Saddle Stitch Finisher side alignment motor (M15) abnormality MJ-1110 • The side alignment motor (M15) is not rotating or the jog is not moving normally. • The [CBC0] error also occurs when the error [EF15] has occurred consecutively for 3 times.
• Causes: Side alignment motor (M15) Saddle control PC board (SDL)
• Remedy: Saddle stitch unit Is there any mechanical problem when the jog is moved? Correct if so. Side alignment motor (M15) • Harness check • Connector check (CN4) Saddle control PC board (SDL) • Connector check (CN4) • Board check

• Code: CBE0
• Description: Saddle Stitch Finisher folding motor (M17) abnormality MJ-1110 * You receive a [CBE0] error when the [EF17] error occurs three times in succession. An encoder pulse interruption error or rotation abnormality occurs in the saddle stitch finisher folding motor.
• Causes: Folding motor encoder sensor (S34) Folding motor (M17) Saddle control PC board (SDL)
• Remedy: Folding motor encoder sensor (S34) • Sensor check (S34) • Connector check (CN13) • Harness check Folding motor (M17) • Harness check • Connector check (CN19) Saddle control PC board (SDL) • Connector check (CN13, CN19) • Board check

• Code: CC02
• Description: Stack exit roller nip home position detection error. MJ-1042
• Causes: Stack exit roller shift motor (M6) Stack exit roller home position sensor (S13)
• Remedy: Stack exit roller shift motor (M6) Stack exit roller home position sensor (S13) The stack exit roller home position sensor (S13) does not detect that the exit roller is not at the upper position after the stack exit roller motor (M6) has been driven in the specified time when the exit roller is moved down. The stack exit roller home position sensor (S13) does not detect that the exit roller is at the upper position after the stack exit roller shift motor (M6) has been driven in the specified time when the exit roller is moved up.

• Code: CC20
• Description: Saddle communication error MJ-1110. Saddle communication error: Communication error between finisher control PC board and saddle control PC board
• Causes: Finisher control PC board (FIN) Saddle control PC board (SDL)
• Remedy: Finisher control PC board (FIN) • Connector check • Harness check • Board check Saddle control PC board (SDL) • Connector check • Harness check • Board check Finisher control PC board (FIN) Update the firmware version of the finisher control PC board (FIN). Saddle control PC board (SDL) Update the firmware version of the saddle control PC board (SDL).

• Code: CC30
• Description: Stack transport motor abnormality * You receive a [CC30] error when the [EA70] error occurs three times in succession. MJ-1110. Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally.
• Causes: Stack transport motor (M8) Finisher control PC board (FIN)
• Remedy: Check item Measures Stack transport belt Move the stack transport belt. Fix any mechanical problem. Stack transport motor (M8) Check if the connector (CN18) on the finisher control PC board is disconnected from the stack transport motor (M8) and the harnesses are open circuited. Correct if so.