• Code: E065
• Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.
• Remedy: If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

• Code: E090
• Description: Image data delay jam: Image data to be printed cannot be prepared
• Remedy: 1) Remove the paper remained in front of the registration sensor. 2) Check if the error is cleared by turning the power OFF and then back ON. 3) Check if the connectors connecting the SYS board, SLG board and PLG board are disconnected. 4) Check if the connectors of the HDD are disconnected. 5) Check if the harnesses connecting the SYS board, SLG board and PLG board are opencircuited. 6) Replace the HDD, SYS board, SLG board and PLG board.

• Code: E110
• Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
• Remedy: Open the jam access cover. Is there any paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check:03-[FAX]ON/[9]/[E]) ↓→ NO → 1) Check if the connector of the registration sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration sensor. 6) Replace the LGC board. YES Is the ADU clutch working? (Perform the output check: 03-222) ↓→ NO → 1) Check if the connector of the ADU clutch is disconnected. 2) Check if the connector CN340 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the ADU clutch. 6) Replace the LGC board. YES Check the rollers in the ADU. Replace them if they are worn out.

• Code: E120
• Description: Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor.
• Remedy: Open the jam access cover. Is there any paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check: 03-[FAX]ON/[9]/[E]) ↓→ NO → 1) Check if the connector of the registration sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration sensor. 6) Replace the LGC board. YES Are the bypass feed clutch and bypass feed sensor working? (Perform the output check: 03-204 and the input check: 03-[FAX]ON/[9]/[D]) ↓→ NO → 1) Check if the connector of the bypass feed clutch is disconnected. 2) Check if the connector CN340 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the bypass feed clutch. 6) Replace the bypass feed sensor. 7) Replace the LGC board. YES Check the rollers in the ADU. Replace them if they are worn out.

• Code: E130
• Description: 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor.
• Remedy: Open the jam access cover. Is there any paper in front of the upper drawer feed sensor? → YES → Remove the paper. NO Is the upper drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[H]) ↓→ NO → 1) Check if the connector of the upper drawer feed sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the upper drawer feed sensor. 6) Replace the LGC board. YES Is the upper drawer feed clutch working? (Perform the output check: 03-201) ↓→ NO → 1) Check if the connector of the upper drawer feed clutch is disconnected. 2) Check if the connector CN341 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the upper drawer feed clutch. 6) Replace the LGC board. YES Check the upper drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E140
• Description: 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor.
• Remedy: Open the side cover. Is there any paper in front of the lower drawer feed sensor? → YES → Remove the paper. NO Is the lower drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[G]) ↓→ NO → 1) Check if the connector of the lower drawer feed sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the lower drawer feed sensor. 6) Replace the LGC board. YES Is the lower drawer feed clutch working? (Perform the output check: 03-202) ↓→ NO → 1) Check if the connector of the lower drawer feed clutch is disconnected. 2) Check if the connector CN341 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the lower drawer feed clutch. 6) Replace the LGC board. YES Check the lower drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E150
• Description: PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor.
• Remedy: Open the PFP side cover. Is there any paper in front of the PFP upper drawer feed sensor? → YES → Remove the paper. NO Is the PFP upper drawer feed sensor working? (Perform the input check: 03-[FAX]OFF/[2]/[D]) ↓→ NO → 1) Check if the connector of the PFP upper drawer feed sensor is disconnected. 2) Check if either of the connectors CN241 or CN243 on the PFP board is disconnected. 3) Check if the connector CN344 on the LGC board is disconnected. 4) Check if the connector pins are disconnected or the harnesses are open circuited. 5) Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 6) Replace the PFP upper drawer feed sensor. 7) Replace the PFP board. 8) Replace the LGC board. YES Is the PFP upper drawer feed clutch working? (Perform the output check: 03-226) ↓→ NO → 1) Check if the connector of the PFP upper drawer feed clutch is disconnected. 2) Check if any of the connectors CN241, CN242 and CN244 on the PFP board is disconnected. 3) Check if the connector CN344 on the LGC board is disconnected. 4) Check if the connector pins are disconnected or the harnesses are open circuited. 5) Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 6) Replace the PFP upper drawer feed clutch. 7) Replace the PFP board. 8) Replace the LGC board. YES Check the PFP upper drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E160
• Description: PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed sensor.
• Remedy: Open the PFP side cover. Is there any paper in front of the PFP lower drawer feed sensor? → YES → Remove the paper. NO Is the PFP lower drawer feed sensor working? (Perform the input check: 03-[FAX]OFF/[4]/[D]) ↓→ NO → 1) Check if the connector of the PFP lower drawer feed sensor is disconnected. 2) Check if either of the connectors CN241 or CN243 on the PFP board is disconnected. 3) Check if the connector CN344 on the LGC board is disconnected. 4) Check if the connector pins are disconnected or the harnesses are open circuited. 5) Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 6) Replace the PFP lower drawer feed sensor. 7) Replace the PFP board. 8) Replace the LGC board. YES Is the PFP lower drawer feed clutch working? (Perform the output check: 03-228) ↓→ NO → 1) Check if the connector of the PFP lower drawer feed clutch is disconnected. 2) Check if any of the connectors CN241, CN242 and CN244 on the PFP board is disconnected. 3) Check if the connector CN344 on the LGC board is disconnected. 4) Check if the connector pins are disconnected or the harnesses are open circuited. 5) Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 6) Replace the PFP lower drawer feed clutch. 7) Replace the PFP board. 8) Replace the LGC board. YES Check the PFP lower drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.