• Code: CC40
• Description: Swing motor abnormality: Swing motor is not rotating or swing unit is not moving normally. [MJ-1024]
• Remedy: MJ-1024 Is the swing unit home position sensor (PI35) normal? NO Replace the sensor. YES Is the wiring between the finisher controller PC board and the swing motor (M36) correct? NO Correct the wiring. YES Is the swing mechanism normal? NO Fix the mechanism. YES 1. Replace the swing motor. 2. Replace the finisher controller PC board.

• Code: CC41
• Description: Paper holder cam home position abnormality: The paper holder cam is not at the home position. [MJ-1101]
• Remedy: MJ-1101 Is there any mechanical problem when the paper holder cam is rotated? ..YES Fix the mechanism. NO Is the harness between the paper holder home position sensor (S6) and the finisher control PC board (CN17) disconnected or open circuited? l ..YES • Reconnect the connector securely. • Replace the harness. NO 1. Replace the paper holder home position sensor (S6). 2. Replace the finisher control PC board.

• Code: CC50
• Description: Horizontal registration motor abnormality: The horizontal registration motor is not rotating normally or the puncher is not moving normally. [MJ-1025 (when MJ-6005 is installed)] Horizontal registration motor abnormality: Horizontal registration motor is not rotating or puncher is not shifting normally. [MJ-1024 (when MJ-6004 is installed)]
• Remedy: MJ-1025 (when MJ-6005 is installed) Is the horizontal registration home position sensor (PI2P) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC board and the horizontal registration home position sensor (PI2P) correct? NO Correct the wiring. YES Is there any problem with the horizontal registration mechanism? YES Fix the mechanism. NO Replace the horizontal registration motor (M2P). Try replacing the punch controller PC board. Is the problem corrected? YES End. NO Replace the finisher controller PC board.
  MJ-1024 (when MJ-6004 is installed) Is the horizontal registration home position sensor (PI61) working normally? NO Replace the sensor. YES Is the wiring between the horizontal registration home position sensor and finisher controller PC board correct? NO Correct the wiring. YES Is the horizontal registration mechanism normal? NO Fix the mechanism. YES 1. Replace the horizontal registration motor (M62). 2. Replace the punch controller PC board. 3. Replace the finisher controller PC board.

• Code: CC51
• Description: Sideways adjustment motor abnormality
• Remedy: MJ-1101 (When MJ-6101 is installed) Is there any paper remaining on the transport path? ..YES Remove the paper. NO Rotate the sideways adjustment motor (M2). Does it rotate smoothly? ..NO Fix the mechanism. YES Are the sideways deviation home position sensor (S3) and its wiring correct? ..NO Replace the sensor. Correct the wiring. YES Is the wiring between the hole punch control PC board (HP) and sideways adjustment motor (M2) correct? ..NO Correct the wiring. YES 1. Replace the punch sideways adjustment motor (M2). 2. Replace the hole punch control PC board (HP).

• Code: CC52
• Description: Skew adjustment motor abnormality
• Remedy: MJ-1101 (When MJ-6101 is installed) Is there any paper remaining on the transport path? ..YES Remove the paper. NO Rotate the skew adjustment motor (M1). Does it rotate smoothly? ..NO Fix the mechanism. YES Are the skew home position sensor (S2) and its wiring correct? ..NO Replace the sensor. Correct the wiring. YES Is the wiring between the hole punch control PC board (HP) and skew adjustment motor (M1) correct? ..NO Correct the wiring. YES 1. Replace the skew adjustment motor (M1). 2. Replace the hole punch control PC board (HP).

• Code: CC60
• Description: Punch motor abnormality: The punch motor is not rotating normally or the puncher is not moving normally. [MJ-1025 (when MJ-6005 is installed)] Punch motor abnormality: Punch motor is not rotating or puncher is not shifting normally. [MJ-1024 (when MJ- 6004 is installed)]
• Remedy: MJ-1025 (when MJ-6005 is installed) Is the punch home position sensor (PI1P) working properly? NO Replace the sensor. YES Is the punch motor clock sensor (PI3P) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC board and sensor correct? NO Correct the wiring. YES Is there any problem with the punching mechanism? YES Fix the mechanism. NO Replace Punch motor (M1P) Try replacing the punch controller PC board. Is the problem corrected? YES End. NO Replace the finisher controller PC board.
  MJ-1024 (when MJ-6004 is installed) Are the punch home position sensor (PI63) and punch motor clock sensor (PI62) working normally? NO Replace the sensors. YES Is the wiring between the sensors and punch controller PC board correct? NO Correct the wiring. YES Is the punching mechanism normal? NO Fix the mechanism. YES 1. Replace the punch motor (M61). 2. Replace the punch controller PC board. 3. Replace the finisher controller PC board.

• Code: CC61
• Description: Punch motor home position detection error
• Remedy: MJ-1101 (When MJ-6101 is installed) Is there any paper remaining on the transport path? ..YES Remove the paper. NO Rotate the punch motor (M3). Does it rotate smoothly? ..NO Fix the mechanism. YES Are the punch home position sensor (S4) and its wiring correct? ..NO Replace the sensor. Correct the wiring. YES Is the wiring between the hole punch control PC board (HP) and punch motor (M3) correct? ..NO Correct the wiring. YES 1. Replace the punch motor (M3). 2. Replace the hole punch control PC board (HP).

• Code: CC71
• Description: Punch ROM checksum error
• Remedy: MJ-1101 (When MJ-6101 is installed) Is the conductor pattern on the hole punch control PC board (HP) open circuited or short circuited? ..YES Replace the hole punch control PC board (HP). NO Replace the finisher control PC board.