• Code: E090
• Description: Image data delay jam: Image data to be printed cannot be prepared.
• Causes: SYS board IMG board LGC board HDD Page memory
• Remedy: Other • Remove the paper remained in front of the registration sensor. • If the error still occurs, check the following. Power • Check if the error is cleared by turning the power OFF and then back ON SYS board • Connector check (SYS board -IMG board) (CN135) • Page memory check • Board check IMG board • Connector check (IMG board -SLG board) (IMG board - LGC board) (CN422, CN423, CN424) • Harness check • Board check LGC board • Connector check (CN319, CN320) • Harness check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board

• Code: E091
• Description: Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware.
• Causes: SYS board IMG board LGC board HDD
• Remedy: Other • Check if there is any paper in the equipment. Remove it if there is. • If the error still occurs, check the following. Power Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check (SYS board -IMG board) (CN135) • Board check IMG board • Connector check (IMG board -SLG board) (IMG board - LGC board) (CN422, CN423, CN424) • Harness check • Board check LGC board • Connector check (CN319, CN320) • Harness check • Board check HDD • Connector check • HDD check

• Code: E0A0
• Description: Image transport ready time-out jam: Image data to be printed cannot be sent.
• Causes: SYS board IMG board LGC board HDD
• Remedy: Other • Remove the paper remained in front of the registration sensor. • If the error still occurs, check the following. Power Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check (SYS board -IMG board) (CN135) • Board check IMG board • Connector check (IMG board -SLG board) (IMG board - LGC board) (CN422, CN423, CN424) • Harness check • Board check LGC board • Connector check (CN319, CN320) • Harness check • Board check HDD • Connector check • HDD check

• Code: E110
• Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
• Causes: Registration sensor ADU motor2 ADU board PFC board LGC board ADU roller
• Remedy: Registration sensor • Sensor check (Perform the input check: 03-[ALL]OFF/[4]/[B], 03-[COPY]ON/[5]/[H]) • Connector check • Harness check ADU motor2 • Motor check (Perform the output check: 03-144) • Connector check (CN491, CN495) • Harness check LGC board • Connector check (CN309) • Board check Drive unit, Rollers • Gear check • Roller check PFC board • Connector check (CN500, CN515) • Harness check • Board check

• Code: E120
• Description: Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor.
• Causes: Bypass feed sensor Bypass motor Bypass pick-up solenoid ADU board PFC board ADU roller Rollers
• Remedy: Bypass feed sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[A]) • Connector check • Harness check Bypass motor • Motor check (Perform the output check: 03-126) • Connector check • Harness check Bypass pick-up solenoid • Solenoid check (Perform the output check: 03-1254) • Connector check • Harness check ADU board • Connector check (CN490, CN496, CN498) • Board check PFC board • Connector check (CN509) • Harness check • Board check Drive unit, Rollers • Gear check • Roller check

• Code: E130
• Description: 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor.
• Causes: 1st drawer feed sensor Feed motor PFC roller Rollers
• Remedy: 1st drawer feed sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[H]) • Connector check • Harness check Feed motor • Motor check (Perform the output check: 03-120) • Connector check • Harness check PFC board • Connector check (CN512, CN513) • Board check Drive unit, Rollers • Gear check • Roller check

• Code: E140
• Description: 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor.
• Causes: 2nd drawer feed sensor Feed motor PFC roller Rollers
• Remedy: 2nd drawer feed sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[G]) • Connector check • Harness check Feed motor • Motor check (Perform the output check: 03-121) • Connector check • Harness check PFC board • Connector check (CN512, CN513) • Board check Drive unit, Rollers • Gear check • Roller check

• Code: E150
• Description: 3rd drawer misfeeding (Paper not reaching the 3rd drawer feed sensor): The paper fed from the 3rd drawer does not reach the 3rd drawer feed sensor
• Causes: 3rd drawer feed sensor Feed/transfer motor PFC roller Rollers 3rd drawer feed clutch
• Remedy: 3rd drawer feed sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[F]) • Connector check • Harness check Feed/transfer motor • Motor check (Perform the output check: 03-122) • Connector check • Harness check 3rd drawer feed clutch • Clutch check (Perform the output check: 03-250) • Connector check • Harness check PFC board • Connector check (CN502, CN505) • Board check Drive unit, Rollers • Gear check • Roller check