Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 80

Code: C26

Description: Peak detection error
Remedy: Does the exposure lamp light? Yes • Check the connectors on the CCD and SLG boards for disconnection. • Check the shading plate on the rear of the original scale for dirt. • Check the CCD board for breaks and short-circuits. • Check the SLG board for breaks and short-circuits. • Replace the lens unit. • Replace the SLG board. No • Check the lamp connectors for disconnection. • Check the thermostat to see if it has blown. • Check electrical continuity of the lamp. • Check SLG board connector pins J9-22, 23, 24, 25 and 26 for disconnection and the harness for breaks and short-circuits. • Check the SLG board for breaks and short-circuits. • Replace the SLG board. • Replace the lamp regulator

Code: C27

Description: (Home switch does not turn OFF within a fixed time) Carriage initialization error
Remedy: The carriage moves only slightly in the feed direction, or the carriage stays is at a position other than the home position and does not move. Yes Check the circuits on the SLG and SDV boards for troubles. No • Check the connector pins for disconnection and the harness for breaks and short-circuits. • Check the SDV board for breaks and short-circuits. • Check the SLG board for breaks and short-circuits. • Replace the SDV board. • Replace the SLG board.

Code: C28

Description: (Home switch does not turn ON within a fixed time) Carriage initialization error
Remedy: Is a loud sound emitted after the carriage bumps into the home position? Yes Cause: The home switch does not turn ON. • Make sure that the switch connector is connected. • Check the circuits on the SLG and SDV boards for troubles. No Cause: The carriage is located at the home position and does not move. • Check the connector pins for disconnection and the harness for breaks and short-circuits. • Check the SDV board for breaks and short-circuits. • Check the SLG board for breaks and short-circuits. • Replace the SDV board. • Replace the SLG board.

Code: C29

Description: Exposure lamp disconnection detected
Remedy: Does the exposure lamp light? Yes • Check the connectors on the CCD and SLG boards for disconnection. • Check the shading plate on the rear of the original scale for dirt. • Check the CCD board for breaks and short-circuits. • Check the SLG board for breaks and short-circuits. • Replace the lens unit. • Replace the SLG board. No • Check the lamp connectors for disconnection. • Check the thermostat to see if it has blown. • Check electrical continuity of the lamp. • Check SLG board connector pins J9-22, 23, 24, 25 and 26 for disconnection and the harness for breaks and short-circuits. • Check the SLG board for breaks and short-circuits. • Replace the SLG board. • Replace the lamp regulator

Code: C36

Description: Main charger wire cleaning operation abnormal
Remedy: (1) Check the main charger. • Is the main charger disconnected? (2) Check the cleaning motor. • Is the motor operating? (3) Replace the LGC board.

Code: C37

Description: Transfer belt operation abnormal
Remedy: (1) Check the transfer belt. • Are the connectors disconnected? • Are the contact switches and limit switches normal? (2) Replace the LGC board.

Code: C41

Description: Thermistor abnormal or heater disconnection at power ON
Remedy: Note) Before carrying out checks (1) and (2) below, first disconnect the power cord to prevent the danger of electric shock. (1) Check the thermistor. • Are the connectors disconnected? • Are the main and sub (end section) thermistors firmly contacting the heat roller? • Are the harness of the main and sub (end section) thermistors broken? (2) Check the heater lamp and SSR. • Is the heater lamp broken? • Is the heater lamp connector disconnected? • Is the thermostat blown? • Is the SSR connector disconnected? • Are the SSR and switching power supplies damaged? (3) Check the LGC board. • Is connector J326 disconnected? • Check the circuits for breaks, short-circuits or other troubles. • Replace the LGC board. (4) Reset the status counter. Carry out the following after you have repaired the location where error [C41] occurred: • Turn the power ON while holding the 0 and 8 keys down. • Enter “400” from the number key pad, and press the START key. • Overwrite currently displayed status counter 1 or 2 to 0, and press the SET or INTERRUPT key to cancel error [C41]. • Turn the power OFF then back ON, and check the machine enters a normal standby state.

Code: C42

Description: Drum thermistor disconnection
Remedy: (1) Check the Drum thermistor connector (the relay connector is attached to the front frame of Cleaner Unit) • Thermistor broken? • Is the connector disconnected? • Is the Pin disconnected? (2) Check the relay connector J728: the connector for the Cleaner Unit) • Is the connector disconnected or about to become so? • Is the pin disconnected out? (3) Replace the LGC board
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie