Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 5500 — Trang 6/7

Code: J6-1

Description: Replace Drum Cartridge - J6-1 Drum End of Life The Drum Cartridge has reached its end of life count.
Causes: • Drum Cartridge • Drum Cartridge CRUM PWB • Engine Control Board
Remedy: 1 Check the Drum Cartridge installation. Was the Drum Cartridge replaced? Go to Step 2. Replace the Drum Cartridge. If the error persists, go to Step 2. 2 Check the Drum Cartridge CRUM PWB installation. Is the Drum Cartridge CRUM PWB installed correctly? Go to Step 3. Correct the installation. 3 Check the Drum Cartridge CRUM PWB connection. Are P126 and P/J419 connected? Go to Step 4. Connect P/126 and P/J419. 4 Check continuity between the Drum Cartridge CRUM PWB and Engine Control Board. 1. Disconnect P/126 and P/J419. 2. Check for continuity at the following: • P126-6 <=> P/J419-1 • P126-5 <=> P/J419-2 • P126-4 <=> P/J419-3 • P126-3 <=> P/J419-4 • P126-2 <=> P/J419-5 Are these conductive? Go to Step 5. Repair the wiring. 5 Check +5 V to the Drum Cartridge CRUM PWB. Is there +5 V across P126-6 (+) <=> ground? Replace the Drum Cartridge CRUM PWB. Replace the Engine Control Board.

Code: J7-1, J7-2

Description: Drum Cartridge Failure - J7-n Comm/NVRAM/Type Error The Drum Cartridge CRUM failed to communicate with the Engine Control Board. • Drum Cartridge Failure - J7-1 DRUM Comm Error • Drum Cartridge Failure - J7-2 DRUM NVRAM Error
Causes: • Drum Cartridge • Drum Cartridge CRUM PWB • Engine Control Board
Remedy: 1 Check the Drum Cartridge installation. Was the Drum Cartridge replaced? Go to Step 2. Replace the Drum Cartridge. If the error persists, go to Step 2. 2 Check the Drum Cartridge CRUM PWB. Is the Drum Cartridge CRUM PWB installed correctly? Go to Step 3. Correct the installation. 3 Check the Drum Cartridge CRUM PWB connection. Are P126 and P/J419 connected? Go to Step 4. Connect P/126 and P/J419. 4 Check continuity between the Drum Cartridge CRUM PWB and Engine Control Board. 1. Disconnect P/126 and P/J419. 2. Check for continuity at the following: • P126-6 <=> P/J419-1 • P126-5 <=> P/J419-2 • P126-4 <=> P/J419-3 • P126-3 <=> P/J419-4 • P126-2 <=> P/J419-5 Are these conductive? Go to Step 5. Repair the wiring. 5 Check +5 V to Drum Cartridge CRUM PWB. Is there +5 V across P126-6 (+) <=> ground? Replace the Drum Cartridge CRUM PWB. Replace the Engine Control Board.

Code: J7-3

Description: Replace Incorrect Drum Cartridge - J7-3 DRUM Type Mismatch The Drum Cartridge CRUM PWB indicates a non-Xerox Drum Cartridge is installed.
Causes: • Drum Cartridge • Drum CRUM PWB • Engine Control Board
Remedy: 1 Check the Drum Cartridge installation. Was the Drum Cartridge replaced? Go to Step 2. Replace the Drum Cartridge. If the error persists, go to Step 2. 2 Check the Drum Cartridge CRUM PWB. Is the Drum Cartridge CRUM PWB installed correctly? Go to Step 3. Correct the installation. 3 Check the Drum Cartridge CRUM PWB connection. Are P126 and P/J419 connected? Go to Step 4. Connect P/126 and P/J419. 4 Check continuity between the Drum Cartridge CRUM and Engine Control Board. 1. Disconnect P/126 and P/J419. 2. Check for continuity at the following: • P126-6 <=> P/J419-1 • P126-5 <=> P/J419-2 • P126-4 <=> P/J419-3 • P126-3 <=> P/J419-4 • P126-2 <=> P/J419-5 Are these conductive? Go to Step 5. Repair the wiring. 5 Check +5 V to the Drum Cartridge CRUM PWB. Is there +5 V across P126-6 (+) <=> ground? Replace the Drum Cartridge CRUM PWB. Replace the Engine Control Board.

Code: J8-1, J8-2

Description: Toner Cartridge Failure - J8-n Toner Comm/Read/Write The Toner CRUM PWB failed to communicate with the Engine Control Board.
Causes: • Toner Cartridge • Toner Cartridge CRUM PWB • Engine Control Board
Remedy: 1 Check the Toner Cartridge installation. Was the Toner Cartridge replaced? Go to Step 2. Replace the Toner Cartridge. If the error persists, go to Step 2. 2 Check the Toner Cartridge CRUM PWB. Is the Toner Cartridge CRUM PWB installed correctly? Go to Step 3. Correct the installation. 3 Check the Toner Cartridge CRUM PWB connection. Are P127 and P/J419 connected? Go to Step 4. Connect P127 and P/J419. 4 Check continuity between the Toner CRUM PWB and Engine Control Board. 1. Disconnect P127 and P/J419. 2. Check for continuity at the following: • P127-6 <=> P/J419-6 • P127-5 <=> P/J419-7 • P127-4 <=> P/J419-8 • P127-3 <=> P/J419-9 • P127-2 <=> P/J419-10 Are these conductive? Go to Step 5. Repair the wiring. 5 Check +5 V to the Toner Cartridge CRUM PWB. Is there +5 V across P127-6 (+) <=> ground? Replace the Toner Cartridge CRUM PWB. Replace the Engine Control Board.

Code: J8-3

Description: Replace Incorrect Toner Cartridge - J8-3 Toner Cartridge Type Mismatch. • Replace Incorrect Toner Cartridge - J8-3 Toner Cart. type mismatch • Non-Xerox Toner Cartridge
Causes: • Toner Cartridge • Toner Cartridge CRUM PWB • Engine Control Board
Remedy: 1 Check the Toner Cartridge installation. Was a Xerox Toner Cartridge replaced? Go to Step 2. Replace with a Xerox Toner Cartridge. If the error persists, go to Step 2. 2 Check the Toner Cartridge CRUM PWB installation. Is the Toner Cartridge CRUM PWB installed correctly? Go to Step 3. Correct the installation. 3 Check the Toner Cartridge CRUM PWB connection. Are P127 and P/J419 connected? Go to Step 4. Connect P127 and P/J419. 4 Check continuity between the Toner CRUM PWB and Engine Control Board. 1. Disconnect P127 and P/J419. 2. Check for continuity at the following: • P127-6 <=> P/J419-6 • P127-5 <=> P/J419-7 • P127-4 <=> P/J419-8 • P127-3 <=> P/J419-9 • P127-2 <=> P/J419-10 Are these conductive? Go to Step 5. Repair the wiring. 5 Check +5 V to the Toner Cartridge CRUM PWB. Is there +5 V across P127-6 (+) <=> ground? Replace the Toner Cartridge CRUM PWB. Replace the Engine Control Board.

Code: U0-1, U1-1

Description: Main Motor Failure The Main Motor stopped or did not start on time.
Causes: • Motor Assembly • Engine Control Board
Remedy: 1 Check the Motor Assembly installation. Remove the Upper Rear Cover . Is the Motor Assembly installed correctly? Go to Step 2. Correct the installation. 2 Test Motor Assembly operation.Run the Service Diagnostics Main Motor test. Does the motor run? Go to Step 6. Go to Step 3. 3 Check the Motor Assembly connection. Are P/J214 and P/J408 connected? Go to Step 4. Connect P/J214 and P/J408. 4 Check continuity between the Motor Assembly and Engine Control Board. Does each wire conduct between P/J214 <=> P/J408? Go to Step 5. Repair the wiring. 5 Check for +24 V to the Motor Assembly. Is there +24 V across P/J214-1/-2 (+) <=> ground? Replace the Motor Assembly. Replace the Engine Control Board.

Code: U1-4

Description: Drum Motor Failure - U1-4 Drum Motor Failure The Drum Cartridge drive motor failed.
Causes: • Drum Cartridge • Fuser • Motor Assembly • Engine Control Board
Remedy: 1 Check the Fuser installation. Is the Fuser installed properly? Go to Step 2. Correct the Fuser. 2 Check the Drum Cartridge installation. Is the Drum Cartridge installed properly? Go to Step 3. Correct the installation. 3 Test the Drum Motor. Run the Service Diagnostics Drum Motor test. Does the motor run? Go to Step 4. Verify motor installation. Go to Step 5. 4 Check the Motor Assembly installation. Remove the Upper Rear Cover. Is the Motor installed properly? Replace the Engine Control Board. Correct the installation. 5 Check Drum Motor rotation. Can the rotor be rotated by hand without excessive load? Go to Step 6. Verify installation. 6 Check the Motor Assembly connection. Are P/J214 and P/J408 connected? Go to Step 7. Connect the Motor. 7 Check continuity between the Motor Assembly and Engine Control Board. Is there continuity on each wire between P/ J214 <=> P/J408? Go to Step 8. Repair the wiring. 8 Check for +24 V to the Motor. Is there +24 V across P/J214-1/-2 (+) <=> ground? Replace the Motor Assembly. Replace the Engine Control Board.

Code: U3-3

Description: Laser Unit Failure - U3-3 Laser Power The Laser Assembly has failed.
Causes: • Drum Cartridge • Laser Assembly • Engine Control Board
Remedy: 1 Check the Drum Cartridge installation. Is the Drum Cartridge installed properly? Go to Step 2. Correct the installation. 2 Check the Laser Assembly installation. Is the Laser Assembly installed properly? Go to Step 3. Correct the Laser Assembly. 3 Check the Laser Assembly connection. Are P/J140 and P/J406 connected? Go to Step 4. Connect the Laser. 4 Check the Laser Assembly connections. Are P/J130, P/J620 and P/J406 connected? Go to Step 5. Connect P/J130, P/J620 and P/ J406. 5 Check continuity between the Laser Assembly and the Engine Control Board. Is there continuity on each wire between P/ J140 <=> P/J406? Go to Step 6. Repair the wiring. 6 Check continuity between the Laser Assembly and the Engine Control Board. Is there continuity on each wire between P/ J130 <=> P/J406? Go to Step 7. Repair the wiring. 7 Check for +5 V to the Laser Assembly. Is there +5 V across P/J140-8 (+) <=> ground? Go to Step 8. Replace the Engine Control Board. 8 Check for +24 V to the Laser. Is there +24 V across P/J130-5 (+) <=> ground? Replace the Laser Assembly REP 5.10). Replace the Engine Control Board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie