Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 6300 — Trang 7/7

Code: 78, 79

Description: Engine Firmware Failure The Engine Control Board detected a firmware error. Code 78: CRUM Data Error Code 79: This is a generic Engine Firmware Failure code generated when any other Engine Firmware Failure code fails to report to the controller properly.
Causes: • Engine Control Board, PL9.1.16
Remedy: 1 Does the error persist after the printer power is cycled? Replace the Engine Control Board. Complete

Code: 80

Description: Disk Failure An error was detected in the Hard Disk.
Causes: • Hard Drive PL9.1.25 • Image Processor Board PL9.1.3
Remedy: 1 Check the Hard Drive installation. Is the Hard Drive properly installed? Go to Step 2. Correct the installation. 2 Replace the Internal Hard Drive. Does the error persist? Replace the Image Processor Board Complete

Code: 83

Description: Engine NVRAM Error Engine NVRAM is corrupted or receiving corrupt data from a CRUM.
Causes: • EEPROM Board, PL9.1.12 • Imaging Unit, PL6.1.1 • Fuser, PL5.1.1 • Engine Control Board, PL9.1.16
Remedy: 1 Cycle printer power. Does the error persist? Go to Step 2. Complete 2 Reinstall the Imaging Unit and Fuser. Cycle printer power. Does the error persist? Go to Step 3. Complete 3 Replace the Imaging Unit. Cycle printer power. Does the error persist? Go to Step 4 Complete 4 Replace the Fuser. Cycle printer power. Does the error persist? Go to Step 5 Complete 5 Replace the EEPROM Board. Cycle printer power. Does the error persist? Replace the Engine Control Board. Complete

Code: 86 ... 89

Description: [Y] [M] [C] [K] Toner Cartridge Failure A CRUM error has occurred for the indicated Toner Cartridge. Code 86: Cyan Toner Cartridge Failure Code 87: Magenta Toner Cartridge Failure. Code 88: Yellow Toner Cartridge Failure Code 89: Black Toner Cartridge Failure
Causes: • Toner Cartridge, PL7.2.8 • RFID Harness, PL7.2.17 • RFID2 Harness, PL7.2.16 • CRUM Reader, PL7.2.12
Remedy: 1 Check Toner Cartridge installation. Are the Toner Cartridges properly installed? Go to Step 2. Correct the installation. 2 Replace the affected Toner Cartridge. Does the error persist after a genuine Xerox Toner Cartridge is installed? Go to Step 3. Complete 3 Check the CRUM Reader connection. Is P/J341 connected to the harness? Go to Step 4. Connect the CRUM Reader Board 4 Replace the CRUM Reader. Does the error persist? Go to Step 5. Complete 5 Check all pins on the RFID2 Harness PL7.2.16 for continuity. 1. Disconnect P/J341 and P/J3411. 2. Check continuity between J341 <=> J3411. Go to Step 6. Replace the RFID2 Harness. 6 Check all pins on the RFID Harness PL7.2.17 for continuity. 1. Disconnect P/J3411 and P/J34. 2. Check continuity between P3411 <=> J34. Replace the Engine Control Board. Replace the RFID Harness.

Code: 90 ... 99

Description: Code 90: Cyan CRUM ID Error Code 91: Magenta CRUM ID Error Code 92: Yellow CRUM ID Error Code 93: Black CRUM ID Error Code 96: Non-Xerox Cyan Toner Cartridge Detected Code 97: Non-Xerox Magenta Toner Cartridge Detected Code 98: Non-Xerox Yellow Toner Cartridge Detected Code 99: Non-Xerox Black Toner Cartridge Detected. Replace [Y] [M] [C] [K] Toner Cartridge The CRUM Reader detected a CRUM ID error or a Non-Xerox Toner Cartridge. An empty or non-genuine Xerox cartridge, a fatal cartridge error, or a fatal printer error can cause this error. Check for an error code in the help text prior to troubleshooting. If a code in the range of 232~235 appears, or no code is present, see "Replace [Y] [M] [C] [K] Toner Cartridge or [Y] [M] [C] [K] Toner Is Low". A Non-Xerox Toner Cartridge warning message occurs when the printer detects the presence of Non-Xerox Toner. The customer can continue to print by selecting use it on the Control Panel when queried whether to use the Non-Xerox cartridge. If the customer chooses Do Not Use, the warning message is replaced by the Replace [C] [M] [Y] [K] Toner Cartridge error message and the associate codes (96 ~ 99) appear in the help text.
Causes: • Toner Cartridge, PL7.2.8 • RFID Harness, PL7.2.17 • RFID2 Harness, PL7.2.16 • CRUM Reader, PL7.2.12
Remedy: 1 Check Toner Cartridge installation. Are the Toner Cartridges properly installed? Go to Step 2. Correct the installation. 2 Replace the affected Toner Cartridge. Does the error persist after a genuine Xerox Toner Cartridge is installed? Go to Step 3. Complete 3 Check the CRUM Reader Board connection. Is P/J341 connected to the harness? Go to Step 4. Reconnect the CRUM Reader Board 4 Replace the CRUM Reader Board. Does the error persist? Go to Step 5. Complete 5 Check all pins on the RFID2 Harness PL7.2.16 for continuity. 1. Disconnect P/J341 and P/J3411. 2. Check continuity between J341<=>J3411. Go to Step 6. Replace the RFID2 Harness. 6 Check all pins on the RFID Harness PL7.2.17 for continuity. 1. Disconnect P/J3411 and P/J34. 2. Check continuity between P3411<=>J34. Replace the Engine Control Board. Replace the RFID Harness.

Code: 94

Description: Non-Phaser 6300/6350 Fuser A CRUM-ID error indicates that a non-Phaser 6300 Fuser is installed.
Causes: • Fuser, PL5.1.1 • FSR/ADC Harness, PL5.2.28 • Engine Control Board, PL9.1.16
Remedy: 1 Check the Fuser part number. Is the Fuser a genuine Xerox part. Go to Step 2. Replace the Fuser. 2 Check the Fuser for damage. Is the Fuser damaged? Replace the Fuser. Go to Step 3. 3 Check Fuser installation. Remove and reinstall the Fuser. Does the error persist? Go to Step 4 Complete 4 Replace the Fuser. Does the error persist? Go to Step 5. Complete 5 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J361. 2. Check continuity between J36<=>J361. Replace the Engine Control Board. Replace the FSR/ ADC Harness.

Code: 95

Description: Non-Xerox Imaging Unit A Imaging Unit CRUM I.D. error indicates that a non-Xerox Imaging Unit is installed.
Causes: • Imaging Unit, PL6.1.1 • CRUM Board, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9
Remedy: 1 Check the Imaging Unit part number. Is the Imaging Unit a genuine Xerox Phaser 6300/6350 part? Go to Step 2. Replace the Imaging Unit. 2 Check the Imaging Unit for damage. Is the Imaging Unit damaged? Replace the Imaging Unit. Go to Step 4. 3 Replace the Imaging Unit. Does the error persist? Go to Step 5. Complete 4 Check the CRUM connection. Is P/J710 connected to the harness? Go to Step 3. Connect the CRUM 5 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J710 <=> J484. Go to Step 4. Replace the PHD2 Harness. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J484. 2. Check continuity between J48<=>P484. Go to Step 5. Replace the FAN/ PHD/MOT Harness. 7 Replace the Imaging Unit. Does the error persist? Replace the Engine Control Board. Complete
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie