Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 7760 — Trang 20/39

Code: 009-924

Description: Waste Toner Cartridge Full The Waste Toner Cartridge is full.
Remedy: Replace the Waste Toner Cartridge (PL 4.1). Check the Full Toner Sensor for contaminants.
If the problem persists, go to RAP 009-358, Waste Cartridge Full Toner Sensor Failure.

Code: 009-925

Description: Waste Toner Cartridge Installation The Waste Toner Cartridge was not installed correctly.
Remedy: There is +5 VDC from J408-5 on the Engine Control Board (MCU PWB) to GND. Y↓N→There is +5 VDC from FS135 on the Waste Toner Cartridge Interlock Switch to GND. Y↓N→Check the wire from J511B on the +5 VDC LVPS to FS135 on the Waste Toner Cartridge Interlock Switch. There is +5 VDC from FS135 on the Waste Toner Cartridge Interlock Switch to GND. Y↓N→Replace the Waste Toner Cartridge Interlock Switch (PL 4.1). Check the wire between J511B on the +5 VDC LVPS and FS134 on the Waste Toner Cartridge Interlock Switch and the MCU PWB J408-5 for an open circuit or poor contact. Check the connector J408-5 between the MCU PWB and GND. If no problems are found, replace the Engine Control Board (MCU PWB) (PL 13.1).

Code: 009-926

Description: Black Imaging Unit End of Life The Black Imaging Unit must be replaced.
Remedy: Replace the Black Imaging Unit (PL 4.1). The problem is corrected. Y↓N→Replace the Engine Control Board (MCU PWB) (PL 13.1). Return to Service Call Procedures.

Code: 009-927

Description: Cyan Imaging Unit End of Life The Cyan Imaging Unit must be replaced.
Remedy: Replace the Cyan Imaging Unit (PL 4.1). The problem is corrected. Y↓N→Replace the Engine Control Board (MCU PWB) (PL 13.1). Return to Service Call Procedures.

Code: 009-928

Description: Magenta Imaging Unit End of Life The Magenta Imaging Unit must be replaced.
Remedy: Replace the Magenta Imaging Unit (PL 4.1). The problem is corrected. Y↓N→Replace the Engine Control Board (MCU PWB) (PL 13.1). Return to Service Call Procedures.

Code: 009-929

Description: Yellow Imaging Unit End of Life The Yellow Imaging Unit must be replaced.
Remedy: Replace the Yellow Imaging Unit (PL 4.1). The problem is corrected. Y↓N→Replace the Engine Control Board (MCU PWB) (PL 13.1). Return to Service Call Procedures.

Code: 009-930

Description: Black Imaging Unit Not Detected The control logic detected that Black Imaging Unit is not installed.
Remedy: Swap the Black Imaging Unit with Imaging Unit (Y), (C) or (M). The problem is corrected. Y↓N→Check that J405 on the Engine Control Board (MCU PWB) and J622 are connected. Check the wires for an open or short. If the check is OK, replace the Engine Control Board (MCU PWB) (PL 13.1). Replace the defective Imaging Unit (PL 4.1).

Code: 009-931

Description: Cyan Imaging Unit Not Detected The control logic detected that Cyan Imaging Unit is not installed.
Remedy: • Ensure Cyan Imaging Unit is installed correctly. • Turn the printer power Off, then On. Swap the Cyan Imaging Unit with Imaging Unit (Y), (K) or (M). The problem is corrected. Y↓N→Check that J405 on the MCU PWB and J622 are connected. Check the wires for an open or short. If the check is OK, replace the Engine Control Board (MCU PWB) (PL 13.1). Replace the defective Imaging Unit (PL 4.1).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie