Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 7760 — Trang 3/39

Code: 003-948

Description: Tray 4 Out of Place Tray 4 not in position.
Remedy: Ensure Tray 4 is closed. Turn the printer power Off, then On. The problem continues. Y↓N→Return to the Service Call Procedures. The machine is equipped with a 3TM. Y↓N→Go to RAP 007-276, Tray 4 Paper Size Sensor (TTM). Go to RAP 007-272, Tray 4 Paper Size Sensor (3TM).

Code: 003-949

Description: Tray 5 Out of Place Tray 5 not in position.
Remedy: Ensure Tray 5 is closed. Turn the printer power Off, then On. The problem continues. Y↓N→Return to the Service Call Procedures. The machine is equipped with a 3TM. Y↓N→Go to RAP 007-277, Tray 5 Paper Size Sensor (TTM). Go to RAP 007-273, Tray 5 Paper Size Sensor (3TM).

Code: 003-950

Description: Tray 2 No Paper Sensor Tray 2 No Paper Sensor failure.
Remedy: Remove Tray 2. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Actuate Tray 2 No Paper Sensor (PL 2.4). The display changes. Y↓N→Check the circuit of the Tray 2 No Paper Sensor. Refer to Transmissive Sensor Procedure for troubleshooting procedure. • Go to RAP 007-281 (Tray 2, 3, 4, 5) Lift Failure) and check the circuit of the Tray 2 Level Sensor. • Ensure that the connectors shown in the circuit diagram are securely connected and that the wires are not damaged. • Replace the Tray 2 No Paper Sensor (PL 2.4). • If the problem persists, replace the Engine Control Board (MCU PWB) (PL 13.1).

Code: 003-951

Description: Tray 3 No Paper Sensor Tray 3 No Paper Sensor failure.
Remedy: Remove Tray 3. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Actuate the Tray 3 No Paper Sensor (TTM or - 3TM). The display changes. Y↓N→Check the circuit of the Tray 3 No Paper Sensor (TTM or 3TM). Refer to Transmissive Sensor Procedure for troubleshooting procedure. Press Stop. • Go to the 007-281 RAP and check the circuit of the Tray 3 No Paper Sensor (PL 2.4). • Ensure that the connectors shown in the circuit diagram (TTM or 3TM) are securely connected and that the wires are not damaged. • Replace the Tray 3 No Paper Sensor (PL 2.4). • If the problem persists, replace the Tray Module PWB (PL 16.15 - TTM or PL 15.9 - 3TM).

Code: 003-952

Description: Tray 4 No Paper Sensor Tray 4 No Paper Sensor failure.
Remedy: Remove Tray 4. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Actuate the Tray 4 No Paper Sensor. The display changes. Y↓N→Check the circuit of the Tray 4 No Paper Sensor (TTM or 3TM). Refer to the Transmissive Sensor Procedure for troubleshooting procedure. • Go to the 007-281 RAP (Tray Lift Failure) and check the circuit of the Tray 4 No Paper Sensor (PL 2.4). • Ensure that the connectors shown in the circuit diagram (TTM or 3TM) are securely connected and that the wires are not damaged. • Replace the Tray 4 No Paper Sensor (PL 2.4). • If the problem persists, replace the Tray Module PWB (PL 16.15 - TTM or PL 15.9 - 3TM).

Code: 003-953

Description: Tray 5 No Paper Sensor Tray 5 No Paper Sensor failure.
Remedy: Remove Tray 5. Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Actuate the Tray 5 No Paper Sensor (TTM or - 3TM). The display changes. Y↓N→Check the circuit of the Tray 5 No Paper Sensor (TTM or 3TM). Refer to Transmissive Sensor Procedure for troubleshooting procedure. • Go to the 007-281 RAP (Tray Lift Failure) and check the circuit of the Tray 5 No Paper Sensor (PL 2.4). • Ensure that the connectors shown in the circuit diagram (TTM or 3TM) are securely connected and that the wires are not damaged. • Replace the Tray 5 No Paper Sensor (PL 2.4). • If the problem persists, replace the Tray Module PWB (PL 16.15 - TTM or PL 15.9 - 3TM).

Code: 003-954

Description: Tray 1 (MPT) No Paper Sensor Tray 1 (Bypass) no paper.
Remedy: Enter Service Diagnostics Menu: Printer Menu > Troubleshooting > Service Tools > Printer Status Page > hold the Up and Down buttons simultaneously > Run Service Diagnostics > OK. Actuate the Tray 1 (MPT) No Paper Sensor (PL 2.12). The display changes. Y↓N→Check the circuit of the Tray 1 (MPT) No Paper Sensor. Refer to Transmissive Sensor Procedure for troubleshooting procedure. • Ensure that the connectors shown in the circuit diagram are securely connected and that the wires are not damaged. • Replace the Tray 1 No Paper Sensor (PL 2.12). • If the problem persists, replace the Engine Control Board (MCU PWB) (PL 13.1).

Code: 004-322

Description: Main Motor Fail Main Motor failure.
Remedy: 1 Enter Service Diagnostics Menu (refer to Control Panel Diagnostics). Does the Main Motor run in diagnostics? Go to step 2. Go to step 3. 2 Does the voltage at P/J 203-8 change from +3.3 VDC to 0 VDC when the motor is turned on and off in Service Diagnostics? Check the wiring from J 203-8 to J536-3 for open or shorted to ground. If the wiring is OK, replace the Interface Board. Replace the Main Drive Motor Assembly. 3 Check P/J 203-1 and P/J 203-2 for +24 VDC. Do both pins have +24 VDC? Go to step 4. Replace the Interface PWB. 4 Turn off the printer and check the wiring between J203 and J 536 for an open condition or short to ground. Is the wiring OK? Replace the Interface PWB. Repair the wiring harness.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie