Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 8860 MFP — Trang 4/14

Code: 23,133.4x

Description: RAM Faults An RAM DIMM error has occurred. The following troubleshooting procedure applies to these errors: 23,133.4x The system detected an NVRAM fault during operation.
Causes: SDRAM, PL 5.0 or PL 5.1 Electronics Module, PL 5.0 or PL 5.1 (8860) Electronics Module -
Remedy: • Reseat RAM devices and retest. • If the problem persists, follow the procedure below.
1 Reseat the SDRAM devices in the Electronics Module. Does the problem persist? Go to Step 2. Complete. 2 Replace SDRAM. Does the problem persist? Replace the Electronics Module). Complete.

Code: 26,0XX.6x

Description: Printing Faults A printing process error has occurred. The following troubleshooting procedure applies to these errors: 26,0xx.6x A printing process fault occurred during operation. 26,962.64 A fall out code fault.
Causes:
Remedy: • Reset NVRAM and retest. • If the problem persists, follow the procedure below.
Check the fault history and troubleshoot the error listed immediately prior to these codes. Otherwise, reboot the system to clear these error conditions.

Code: 27,0XX.6x

Description: Profile Library A profile library error has occurred. The following troubleshooting procedure applies to these errors: 27,0xx.6x A printing process fault occurred during operation.
Causes:
Remedy: • Reset NVRAM and retest. • If the problem persists, follow the procedure below.
Check system ground integrity.

Code: 29,0XX.6x

Description: Jam Manager Faults A software error has occurred. The following troubleshooting procedure applies to these errors: 29,0XX.6x Jam Manager program faults.
Causes: NVRAM, PL 5.0
Remedy: • Reset NVRAM and retest. • If the problem persists, follow the procedure below.
1 Reseat all Electronics Module connections. Does the problem persist? Go to Step 2. Complete. 2 Check ground integrity. Are the system grounds connected? Reset NVRAM. If the error persists, replace the NVRAM device. Reconnect the system grounds.

Code: 3,0XX.6x

Description: IPC Program Faults A firmware communications error has occurred. The following troubleshooting procedure applies to these errors:
Causes: NVRAM, PL 5.0
Remedy: • Reset NVRAM and retest. • If the problem persists, follow the procedure below.
1 Reseat all Electronics Module connections. Does the problem persist? Go to Step 2. Complete. 2 Check ground integrity. Are the system grounds connected? Reset NVRAM. If the error persists, replace the NVRAM device. Reconnect the system grounds.

Code: 31,001.40

Description: Mechanical Initialization Jam A software error has occurred. The following troubleshooting procedure applies to this error: 31,001.40 Mechanical initialization jam fault.
Causes: Media Drive Assy, PL 4.0 Left Side Harness (2/2) -
Remedy: • Check routing of tray sensor harnesses. • Check that the Take Away Rollers are free of obstructions. • If the problem persists, follow the procedure below.
1 Check the Take Away Rollers. Do the rollers show signs of excessive wear or damage? Replace the affected roller. Go to Step 2. 2 Test the Media Drive. Run the Service Diagnostics Paper Path Drive test. Does the Media Drive operate correctly? Go to Step 4. Go to Step 3. 3 DId the Media Drive run extremely fast? Replace the Media Drive Assembly. Go to Step 4. 4 Check the rollers. Remove the Media Drive Assembly and check each roller for binding or drag. Do the rollers rotate correctly? Replace the Media Drive Assembly. Repair or replace rollers.

Code: 31,0XX.6x

Description: Program Faults A software error has occurred. The following troubleshooting procedure applies to these errors:
Causes: NVRAM, PL 5.0
Remedy: • Reset NVRAM and retest. • If the problem persists, follow the procedure below.
1 Reseat all Electronics Module connections. Does the problem persist? Go to Step 2. Complete. 2 Check ground integrity. Are the system grounds connected? Reset NVRAM. If the error persists, replace the NVRAM device. Reconnect the system grounds.

Code: 33,00X.4x

Description: Tray 1 Width Sensor Faults The Paper Width Sensor, located in the Tray 1/Front Door Assembly is reporting out of range values. The following troubleshooting procedure applies to these errors: 33,001.42 Tray 1 width value too low. 33,002.43 Tray 1 width value too high.
Causes: Tray 1/Front Door Assembly, PL 1.0 I/O Board (2/2) -
Remedy: • Check electrical connection to Tray 1 (P/J650). • Check for obstructions or damage to the Media Guides. • If the problem persists, follow the procedure below.
1 Check the Tray 1 Harness connection to the I/O Board (P/J610). Is the connection secure and the harness undamaged? Go to Step 2. Repair or replace the harness. 2 Test the Width Sensors. Run the Service Diagnostics Tray 1 Width Sensor test. Does the sensor operate correctly? Replace the I/O Board. Replace the Tray 1/ Front Door Assembly.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie