Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 3225

Code: 01-100

Description: Front Cover Open Fault The front cover is open or the cover open switch is defective.
Remedy: Check the Actuator on the Front Cover Open Switch. The Actuator moves freely. Y↓N→Replace the Front Cover Open Switch Actuator. (PL-XX) Check the Front Cover Open Switch. The switch is OK. Y↓N→Replace the Front Cover Open Switch. (PL-XX) Check the connection between the Main PWB and the HVPS (BSD 3.1A). The connection is secure. Y↓N→Secure the connection between the Main PWB and HVPS. Replace the HVPS PWB (PL-XX).

Code: 03-410

Description: Paper Mismatch at Tray 1 The size setting for the Paper Tray does not match the paper size loaded in the tray.
Remedy: • Check the media size settings for the tray from the Control Panel. • Adjust the Paper Tray Guides to match the size of the paper that is loaded into the tray. • Place the correct size paper into the tray for the tray size setting.
Remove the tray and inspect the Paper Size Switch for wear or contamination. The switch is operational. Y↓N→Replace the Paper Size Switch (PL-XX). • Replace the Paper Tray (PL-XX) • Replace the Main PWB, (PL-XX)

Code: 03-450

Description: Paper Mismatch at Manual Feed Slot The size setting for the Manual Feed Slot does not match the paper size loaded
Remedy: • Check the media size settings for the tray from the Control Panel. • Adjust the Paper Tray Guides to match the size of the paper that is loaded into the tray. • Place the correct size paper into the tray for the tray size setting.
Inspect the Paper Size Switch for wear or contamination. The switch is operational. Y↓N→Replace the Paper Size Switch (PL-XX). • Replace the Paper Tray (PL-XX). • Replace the Main PWB, (PL-XX).

Code: 03-900

Description: Main PWB Motor Control Chip Fault The Motor Control Chip on the Main PWB is not functioning normally.
Remedy: 1. Switch Off the power then switch On the power. 2. If problem continues, replace the Main PWB, (PL-XX).

Code: 04-500

Description: Main Drive (BLDC) Motor Start Fault The Main Drive (BLDC) Motor did not start within the specified time after the ready signal was sent.
Remedy: Enter Diagnostic Mode. Press the <Menu> button, the <#> button, then using the keypad select: [1934, Diagnostics, Machine Test, EDC Mode, DC330 Component Control, 100 Motor] to start the motor. The motor rotates. Y↓N→Remove the Right Cover and check the motor connector on the Main PWB. The connector on the Main PWB is connected correctly. Y↓N→Reconnect the motor connector. Remove the Duplex paper Guide. Check the motor connector. The connector is OK. Y↓N→Reconnect the connector The Imaging Unit Drive coupler may have overloaded. Remove the Print Cartridge and rotate the Imaging Unit coupler. The Imaging Unit coupler rotates freely. Y↓N→Replace the Imaging Unit. The Main Drive Motor or the Main PWB is defective. Perform the following: • Replace the Main Drive Motor PL 4.1. If problem persists, replace the Main PWB, PL 1.1.

Code: 05-100, 05-900

Description: Paper Jam in Document Feeder Fault The machine has detected a paper jam in the Document Feeder.
Remedy: Inspect the Paper Path Sensor for damage or contamination. Remove any debris from the sensor. Enter Diagnostic Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 102 Sensor, Temp A] to test the Registration Sensor. The sensor is OK. Y↓N→Replace the Paper Path Sensor PL 7.1. Check that the Feed Motor is operating correctly. Select: [Machine Test, EDC Mode, DC330 Component Control, 100 Motor, Feed Motor Slow] The Feed Motor is OK. Y↓N→Check the connection from the Feed Motor to the Main PWB is securely seated. The motor is OK. Y↓N→• Replace the Feed Motor. [PL-XX] • Replace the Document Feed Assembly [PL-XX] Go to SCP 04 Final Actions. Check the paper path drives and clear any jammed sheets from the paper path. If problem persists, replace the Main PWB PL 1.1.

Code: 05-500

Description: Document Feeder Cover Open Fault The Document Feeder or Document Feeder Top Cover is not securely latched.
Remedy: • Close the Document Feeder unit. • Close the Document Feeder top cover.
Remove the top cover and check the connection to the PWB sensor switch. The connection is secure. Y↓N→Secure the connection. Replace the sensor? (switch?)

Code: 06-100, 06-200

Description: Laser Module (LSU) Motor Fault The machine has detected that the Laser Module Drive Motor is not working correctly.
Remedy: Enter Diagnostic Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 110 LSU, LSU Mot1 Run] to test the LSU motor. The motor runs. Y↓N→Check the Main Wire Harness and connectors on the Laser Module. The connections are secure. Y↓N→Disconnect and securely reconnect the harness. Check the harness for a short circuit or open circuit. The harness is OK. Y↓N→Replace the harness. Replace the Laser Module (PL-XX) Go to SCP 04 Final Actions.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie