Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 3225 — Trang 2/5

Code: 07-110

Description: Paper Tray 1 Empty Fault The Tray Empty Sensor failed to detect paper in the tray.
Remedy: Check the Tray Empty Sensor actuator. The actuator moves freely is undamaged. Y↓N→Replace the Empty Sensor actuator (PL-XX). Enter Diagnostic Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 102 Sensor, Tray 1 Empty] to actuate and de actuate the Tray 1 Empty Sensor. The sensor signal changes. Y↓N→Replace the Tray Empty Sensor (PL-XX). If the problem is intermittent, check the circuit of the Tray Empty Sensor. (BSD-tbd)

Code: 07-130

Description: Paper Jam in Tray 1 Fault A paper jam has occurred in Tray 1.
Remedy: Remove Tray 1 and ensure that guides are set correctly. The paper is loaded correctly in the tray. Y↓N→Align the paper in Tray 1 then reinsert the tray. Check the position of the jammed sheet. The lead edge reached the Retard Roll. (Figure 1.) Y↓N→Enter Diagnostics Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 102-Sensor, Feed Sens] to block and clear the Feed Sensor. The sensor is OK. Y↓N→Replace the Feed Sensor (PL-XX). In Diagnostics Mode, go to [101-Clutch, Tray 1 Pick up] to energize the clutch. The clutch engages. Y↓N→Replace the Tray 1 Pick up (Feed) Clutch (PL-XX). Perform SCP Final Actions. Remove any jammed paper. Check the following for wear or damage and replace as required: • Retard Roller (PL-XX) • Pick up (Feed) and Forward Roll Assembly (PL-XX) • Elevator Plate (PL-XX) • Elevator Plate Springs (PL-XX)

Code: 07-500

Description: Manual Feed Slot Paper Empty Fault The Manual Feed Slot Empty Sensor failed to detect paper in the Manual Feed Slot.
Remedy: Check the Manual Feed Slot Empty Sensor actuator. The actuator moves freely and is undamaged. Y↓N→Replace the Empty Sensor Actuator (PL-XX). Block and clear the Manual Feed Slot Empty Sensor. The sensor signal changes. Y↓N→Replace the Tray Empty Sensor (PL-XX). Check the circuit of the Tray Empty Sensor.

Code: 07-530

Description: Paper Feed Fault - Manual Feed Slot The lead edge was not detected by the Paper Feed Sensor.
Remedy: Check the position of the jammed sheet. The lead edge reached the Retard Roll. Y↓N→Enter Diagnostics Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 102-Sensor, Feed Sens] to block and clear the Feed Sensor. The sensor is OK. Y↓N→Replace the Feed Sensor (PL-XX). In Diagnostics Mode, select: [101-Clutch, Registration or PU?] to engage the drive to pick up paper from tray 1. The clutch engages. Y↓N→Replace the Tray 1 Pick up (Feed) Clutch (PL-XX). Perform SCP Final Actions. Check the Paper Feed actuator. The actuator moves freely is undamaged. Y↓N→Replace the Paper Feed actuator. Inspect the Paper Feed Sensor for damage. The sensor is OK. Y↓N→Replace the Paper Feed Sensor. Check the circuit of the Paper Feed Sensor.

Code: 08-100

Description: Paper Feed Fault - Tray 1 The lead edge was not detected by the Paper Feed Sensor
Remedy: Check the Tray 1 Pick up Sensor Actuator. The Actuator moves freely. Y↓N→Replace the Tray 1 Pick up Sensor Actuator (PL-XX). Check the position of the jammed sheet. The lead edge reached the Retard Roll. (Figure 1.) Y↓N→Enter Diagnostics Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 101-Clutch, Tray 1 Pick up] to engage the drive to pick up paper from tray 1 The clutch engages. Y↓N→Replace the Tray 1 Pick up (Feed) Clutch (PL-XX). Check the Paper Feed Actuator. The actuator moves freely. Y↓N→Replace the Paper Feed Actuator. In Diagnostics Mode. Select: [102-Sensor, Feed Sens] to block and clear the Paper Feed Sensor. The signal changes. Y↓N→Replace the Paper Feed Sensor (PL-XX). Perform SCP Final Actions. Check the circuit of the Paper Feed Sensor. (BSD-tbd)

Code: 08-500

Description: Paper Jam in Exit Area Fault The machine has detected a paper jam in the Exit Area.
Remedy: Enter Diagnostics Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 102-Sensor, Feed Sens] to test the Exit Sensor. The Exit Sensor is OK. Y↓N→Replace the Exit Sensor (PL-XX). In Diagnostics Mode, go to [102-Sensor, Registration] to activate and deactivate the Registration Sensor. The signal changes. Y↓N→Replace the Registration sensor. (PL-XX) Inspect the Exit Roller and Drives for wear or damage.. Replace if needed.

Code: 08-600

Description: Paper Jam in Duplex Area Fault The machine has detected a paper jam in the Duplex Area.
Remedy: Check the Exit Sensor Actuator. The actuator moves freely. Y↓N→Replace the Exit Sensor Actuator. Enter Diagnostics Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 102-Sensor, Out Bin Exit Sens] to test the Exit Sensor. The sensor is OK. Y↓N→Replace the Exit Sensor. (PL-XX). Check the following parts for wear or damage and replace if needed: • Duplex Paper Guide• Duplex Gate • Duplex Gate Spring • Duplex Gate Mounting • Paper Guide on Rear Cover Make certain that the Duplex Gate is seated correctly and moves freely without binding.

Code: 08-700

Description: Output Tray Full Fault The Output Tray Full Sensor has detected that the Output Tray is full.
Remedy: Enter Diagnostics Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 102-Sensor, Out Bin Full] to test the Out Bin Full Sensor. The signal changes. Y↓N→• Check that the sensor connector is firmly seated. • Replace the Out Bin Full Sensor. (PL-XX) Check actuator for binding. If the problem is intermittent, replace the Out Bin Full Sensor Actuator. (PL-XX)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie