Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5665 — Trang 7/30

Code: 07-354

Description: Tray 2 Elevator Lift Failure RAP 07-354 Tray 2 stack height sensor did not actuate within the correct time after the feed / elevator motor turned on.
Remedy: Enter dC330 code 07-337 tray 2 stack height sensor, Q07-337. Press Start. Pull out tray 1 and push fully home. The display changes Y↓N→Go to flag 2. Check Q07-337. Refer to: • GP 11 How to Check a Sensor. • P/J275, Tray 1 and 2 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 2 stack height sensor, PL 8.26 Item 8. • Tray 1 and 2 control PWB, PL 7.10 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-020 is run in diagnostics. Enter dC330 code 07-020 tray 1 feed / elevator motor, MOT07-020. Pull out tray 1. Press Start. The motor runs Y↓N→Go to flag 3. Check MOT07-020. Refer to: • GP 10 How to Check a Motor. • P/J275, Tray 1 and 2 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 2 Feed / elevator motor, PL 8.26 Item 6. • Tray 1 and 2 control PWB, PL 7.10 Item 2. Perform the following: • Check the feeder / elevator motor drive gears. • Check the tray 2 stack height mechanism on the feeder assembly, If the fault still occurs then go to 07A Tray 1 and Tray 2 False Paper Level RAP.

Code: 07-355

Description: Tray 3 Elevator Lift Failure RAP 07-355 Tray 3 stack height sensor did not actuate within the correct time after the elevator motor turned on.
Remedy: Enter dC330 code 07-303 tray 3 home switch, S07-303. Press Start. Pull out the tray and push back in. The display changes. Y↓N→Go to Flag 1. Check S07-303. Refer to: • GP 13 How to Check a Switch. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 3 home switch, PL 7.20 Item 4. • HCF control PWB, PL 7.20 Item 2. Enter dC330 code 07-383 tray 3 stack height sensor, Q07-383. Press Start. Pull out tray 3 and manually activate the stack height sensor on the paper feed assembly. The display changes Y↓N→Go to Flag 2. Check Q07-383. Refer to: • GP 11 How to Check a Sensor. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 stack height sensor, PL 8.30 Item 21. • HCF control PWB, PL 7.20 Item 2. Go to P/J396 pin 1 on the HCF control PWB, Flag 4. Manually activate the tray 3 stack limit switch (S07-393) on the paper feed assembly. The voltage changes. Y↓N→Go to Flag 3. Check S07-393. Refer to: • GP 13 How to Check a Switch. • P/J396, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 paper feeder, PL 8.30 Item 2. • HCF control PWB, PL 7.20 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-030 is run in diagnostics. Enter dC330 code 07-030 tray 3 elevator motor, MOT07-030. Pull out tray 3. Press Start. The motor runs Y↓N→Go to Flag 4. Check MOT07-030. Refer to: • GP 10 How to Check a Motor. • P/J395, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 3 elevator motor, PL 7.20 Item 1. • HCF control PWB, PL 7.20 Item 2. Perform the following: • Check elevator cables, PL 7.15 Item 4, PL 7.15 Item 6, PL 7.15 Item 7. • Check elevator motor drive coupling, PL 7.20 Item 1. • Check tray elevator drive gears and drive coupling, PL 7.15. • Check the tray 3 empty sensor actuator, PL 8.30 Item 1. If the fault still occurs then go to 07E Tray 3 or Tray 4 Out of Paper RAP.

Code: 07-360

Description: Tray 4 Elevator Lift Failure RAP 07-360 Tray 4 stack height sensor does not actuate within 7 seconds after the elevator motor is turned on.
Remedy: Enter dC330 code 07-304 tray 4 home switch, S07-304. Press Start. Pull out the tray and push back in. The display changes. Y↓N→Go to Flag 1. Check S07-304. Refer to: • GP 13 How to Check a Switch. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 4 home switch, PL 7.20 Item 4. • HCF control PWB, PL 7.20 Item 2. Enter dC330 code 07-384 tray 4 stack height Sensor, Q07-384. Press Start. Pull out tray 4 and manually actuate the stack height sensor on the paper feed assembly. The display changes. Y↓N→Go to Flag 2. Check Q07-384. Refer to: • GP 11 How to Check a Sensor. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 4 stack height sensor, PL 8.31 Item 13. • HCF control PWB, PL 7.20 Item 2. Go to P/J398 pin 6 on the HCF control PWB, Flag 4. Manually activate the tray 4 stack limit switch (S07-394) on the paper feed assembly. The voltage changes. Y↓N→Go to Flag 3. Check S07-394. Refer to: • GP 13 How to Check a Switch. • P/J398, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 4 paper feeder, PL 8.31 Item 4. • HCF control PWB, PL 7.20 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-040 is run in diagnostics. Enter dC330 code 07-040 tray 4 elevator motor, MOT07-040. Pull out tray 4. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT07-040. Refer to: • GP 10 How to Check a Motor. • P/J397, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 4 elevator motor, PL 7.20 Item 1. • HCF control PWB, PL 7.20 Item 2. Perform the following: • Check elevator cables, PL 7.15 Item 4, PL 7.15 Item 5, PL 7.15 Item 7. • Check elevator motor drive coupling, PL 7.20 Item 1. • Check elevator drive gears and drive coupling, PL 7.15. • Check the tray 4 empty sensor actuator, PL 8.31 Item 1. If the fault still occurs then go to 07E Tray 3 or Tray 4 Out of Paper RAP.

Code: 07-372

Description: Tray 5 Undocked During Run RAP 07-372 Tray 5 was undocked during run when the paper is fed from tray 5.
Remedy: Enter dC330 code 07-372 tray 5 docking switch, S07-372. Press Start. Undock and dock tray 5, . The display changes. Y↓N→Go to Flag 1. Check S07-372. Refer to: • GP 13 How to Check a Switch. • P/J507, Tray 5 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 docking switch, PL 7.64 Item 1 • Tray 5 control PWB, PL 7.68 Item 8 Perform the following: • Check the docking latch on tray 5 is latched onto the machine. • Check the that the rail assembly is located correctly to the machine.

Code: 07-373

Description: Tray 5 Elevator Lift Failure RAP 07-373 A signal was not detected by the encoder when the elevator motor was driving up.
Remedy: Open and close the tray 5 door. The tray moves up. Y↓N→Enter dC330 code 07-306 tray 5 door interlock switch. Press Start. Manually toggle the the door interlock switch. The display changes. Y↓N→Check the wiring to the switch. Go to Flag 1. Check S07-306. Refer to: • GP 13 How to Check a Switch. • P/J507, Tray 5 control PWB • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 door interlock switch, PL 7.60 Item 6 • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 07-402 tray 5 stack height sensor, Q07-402. Press Start. Manually activate the stack height sensor on the paper feed assembly. The display changes Y↓N→Go to Flag 2. Check Q07-402. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 5 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 stack height sensor, PL 8.45 Item 7 • Tray 5 control PWB, PL 7.68 Item 8. Go to PJ504 pin 4 on the Tray 5 control PWB, Flag 3. Manually activate the tray upper limit switch (S07-412) on the paper feed assembly. The voltage changes. Y↓N→Go to Flag 3. Check S07-412. Refer to: • GP 13 How to Check a Switch. • P/J504, Tray 5 control PWB • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 stack upper limit switch, PL 7.68 Item 12 • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 07-406 tray 5 elevator motor encoder sensor, Q07-406. Press Start. Manually lift the motor to activate the sensor. The display changes Y↓N→Go to Flag 4. Check Q07-406. Refer to: • GP 11 How to Check a Sensor. • P/J506, Tray 5 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Elevator motor encoder sensor, PL 7.68 Item 5 • Tray 5 control PWB, PL 7.68 Item 8 Enter dC330 code 07-373 tray 5 elevator motor, MOT07-373. Press Start. The motor runs Y↓N→Go to Flag 5. Check MOT07-373. Refer to: • GP 10 How to Check a Motor. • P/J504, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 5 elevator motor, PL 7.68 Item 4 • Tray 5 control PWB, PL 7.68 Item 8 The tray 5 elevator motor is operating correctly. The tray 5 elevator motor is operating correctly.

Code: 07-374

Description: Tray 5 Elevator Lower Failure RAP 07-374 A signal was not detected by the encoder when the elevator motor was driving down.
Remedy: Open and close the tray 5 door. The tray moves down. Y↓N→Enter dC330 code 07-306 tray 5 door interlock switch. Press Start. Manually toggle the the door interlock switch. The display changes. Y↓N→Check the wiring to the switch and if necessary install a new switch, PL 7.60 Item 6. Go to Flag 1. Check S07-306. Refer to: • GP 13 How to Check a Switch. • P/J507, Tray 5 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 door interlock switch, PL 7.60 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 07-405 tray 5 stack down sensor, Q07-405. Press Start. Manually activate the stack down sensor actuator. The display changes Y↓N→Go to Flag 2. Check Q07-405. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 5 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 stack down sensor, PL 7.68 Item 9. • Tray 5 control PWB, PL 7.68 Item 8. Go to PJ504 pin 6 on the Tray 5 control PWB, Flag 3. Manually activate the tray 5 down limit switch (S07-415) on the paper tray. The voltage changes. Y↓N→Go to Flag 3. Check S07-415. Refer to: • GP 13 How to Check a Switch. • P/J504, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 down limit switch, PL 7.70 Item 2. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 07-406 tray 5 elevator motor encoder sensor, Q07-406. Press Start. Manually lift the motor to activate the sensor. The display changes Y↓N→Go to Flag 4. Check Q07-406. Refer to: • GP 11 How to Check a Sensor. • P/J506, Tray 5 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Elevator motor encoder sensor, PL 7.68 Item 5. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 07-373 tray 5 elevator motor, MOT07-373. Press Start. The motor runs Y↓N→Go to Flag 5. Check MOT07-373. Refer to: • GP 10 How to Check a Motor. • P/J504, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 5 elevator motor, PL 7.68 Item 4. • Tray 5 control PWB, PL 7.68 Item 8. The tray 5 elevator motor is operating correctly. The tray 5 elevator motor is operating correctly.

Code: 08-100

Description: Wait Sensor Jam Entry RAP 08-100 The lead edge of the paper failed to actuate the wait sensor within the correct time from feed sensor 1.
Remedy: Identify the speed of the machine, refer to SCP 7 Machine features. Perform one of the steps that follow: • If the speed of the machine is 35-55 ppm, go to 08-100A Wait Sensor RAP (32-55 ppm) • If the speed of the machine is 65-87 ppm, go to 08-100B Wait Sensor RAP (65-87 ppm).

Code: 08-100A

Description: Wait Sensor Jam RAP (32-55 ppm) 08-100 The lead edge of the paper failed to actuate the wait sensor within the correct time from feed sensor 1.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, (32-55 ppm) PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-101 tray 1 feed sensor, Q08-101. Press Start. Open left hand door and manually actuate the sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-101. Refer to: • GP 11 How to Check a Sensor. • P/J276, Tray 1 and 2 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 1 feed sensor, PL 7.30 Item 25. • Tray 1 and 2 control PWB, PL 7.10 Item 2. Enter dC330 code 08-025 tray 1 and 2 transport motor, MOT08-025. Press Start. The motor Y↓N→Go to Flag 3. Check MOT08-025. Refer to: • GP 10 How to Check a Motor. • P/J273, Tray 1 and 2 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 1 and 2 transport motor, (32-55 ppm) PL 8.25 Item 5. • Tray 1 and 2 control PWB, PL 7.10 Item 2. The transport rolls rotate. Y↓N→Check the drive belt and gears, GP 7, PL 8.25 Item 2, PL 8.25 Item 3. Check the following: • The bearing, shaft and rolls on the transport roll assembly, GP 7, (32-55 ppm) PL 8.25 Item 8. • The idler rolls in the left hand door, GP 7, PL 7.30 Item 2. • The transport drive belt, (32-55 ppm) PL 8.25 Item 2. • The transport rolls for wear, PL 8.25 Item 8. Install new components as necessary.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie