Code :

Code: 2F22
Display: Hardware error. 03130031-2F22 Turn off printer, wait, then turn on again.
Description: Pump shift timeout The target position could not be reached within a predicted operation time +3 seconds during pump operation or no sensor has been detected during a pump operation involving sensor detection.
Remedy: <Supplement> -If the carriage travels heavily towards the stop position: A mechanical load error may be suspected. -Otherwise: The sensor in the purge unit may be at fault.

Code: 2F23
Display: Hardware error. 03130031-2F23 Turn off printer, wait, then turn on again.
Description: Purge motor error A PWM duty of 100% has lasted for 200 msec in a pump operation.
Remedy: <Supplement> -If the motor could not be run at all or has resulted in an error after moving by a slight distance: A. A mechanical load error may be suspected. B. The motor or drive circuit may be at fault. -If the carriage has run more or less out of control and resulted in an error: A. The encoder sensor may be at fault.

Code: 2F24
Display: Cannot cut paper. Lift the release lever and reload the paper.
Description: Cutter shift timeout The cutter failed to reach the home position in time during a cutting operation
Remedy:

Code: 2F25
Display: Hardware error. 03130031-2F25 Turn off printer, wait, then turn on again.
Description: Carriage motor HP not detectable Detected only for the wide format. For the narrow format, the carriage motor HP can be detected when the carriage hits the wall in a full scan following the detection of the HP.
Remedy: Check the carriage HP sensor in I/O mode. <Supplement> -If the motor could not be run at all: A. A mechanical load error may be suspected. B. The motor or drive circuit may be at fault. -If the carriage has resulted in an error after moving at a constant speed: A. The carriage HP sensor may be at fault. -If the carriage has run more or less out of control and resulted in an error: A. The encoder sensor may be at fault.

Code: 2F26
Display: Hardware error. 03130031-2F26 Turn off printer, wait, then turn on again.
Description: Carriage operation disabled -A PWM duty of 100% has lasted for 200 msec in a carriage operation -A collision has been detected in a carriage operation (with the speed predicted from the PWM output value having a deviation of 25 ips or more from the actual speed).
Remedy: <Supplement> -If the motor could not be run at all or has resulted in an error after moving by a slight distance: A. A mechanical load error may be suspected. B. The motor or drive circuit may be at fault. -If the carriage has run more or less out of control and resulted in an error: A. encoder sensor may be at fault.

Code: 2F27
Display: Hardware error. 03130031-2F27 Turn off printer, wait, then turn on again.
Description: Carriage shift timeout The target position could not be reached within a predicted operation time +3 seconds during carriage operation.
Remedy: <Supplement> -If the carriage travels heavily towards the stop position, a mechanical load error may be suspected.

Code: 2F28
Display: Hardware error. 03130031-2F28 Turn off printer, wait, then turn on again.
Description: Lift shift timeout A lift operation has been executed, but no sensor has been detected or a sensor has remained detected.
Remedy: 1. Switch off the printer, then back on. 2. The carriage cannot travel to the lift drive position. 3. The lift drive cam is not engaged. 4. Faulty lift drive sensor 5. Faulty lift drive motor

Code: 2F29
Display: Hardware error. 03030000-2F29 Turn off printer, wait, then turn on again.
Description: LF feeding motor timeout (cut sheet) -The target position could not be reached within a predicted operation time +3 seconds during an LF operation. -The sensor could not be detected during an LF operation involving sensor detection.
Remedy: 1. Replace the feed roller encoder sensor. 2. Replace the feed motor. <Supplement> -If the carriage travels heavily near the stop position, a mechanical load error may be suspected. -If any other symptom is observed, a feeding sensor may be at fault.