• Code: 1100
• Display: Prepare for maint cart replacement.
• Description: Maintenance cartridge near-full (continued usage allowed) Near-full has been detected from the dot count and the usage period (drying time). <Maintenance cartridge detection timings> The presence of a maintenance cartridge is detected at the following timings: 1. Before printing/during printing (twice per second)/at the end of printing/ between pages 2. Before a recovery operation/during a recovery operation (twice per second)/ before opening of the ink supply valve 3. When the cartridge is removed and inserted following the occurrence of an error or warning.
• Remedy: Prepare a maintenance cartridge.

• Code: 1101
• Display: Replace part soon.
• Description: Mist count near-full Waste ink near-full has been detected from the dot count.
• Remedy: Check the parts counter and replace the target unit or Refresh Service Kit. Initialize the parts counter for the target unit after the replacement.

• Code: 1400 ... 140C
• Display: No ink left. Press OK and replace ink tank. Ink tank is empty. Replace the ink tank.
• Description: Ink tank empty (continued use allowed) The ink tank has run out of ink, but a certain volume of ink is reserved in the subtank. (The reserved volume of ink is put to use after the remaining ink falls below the pin check level.) Displayed only on models having a subtank. (XX: Display applicable colors) Last 2 digits: 00:Bk, 01:Y, 02:M, 03:C, 04:PM, 05:PC, 06:MBk1, 07:MBk2, 08:GY, 09:PGY, 0A:R, 0B:B, 0C:G
• Remedy: 1. Replace the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.)

• Code: 1410 ... 141C
• Display: No ink tank loaded. Check ink tank.
• Description: Ink tank not installed (continued use allowed) The ink tank is not installed but a sufficient volume of ink is left in the subtank. Displayed only on models having a subtank. This occurs in cases such as when the ink tank cover is opened during printing, and the ink tank is removed. (XX: Displays applicable colors) Last 2 digits: 10:Bk, 11:Y, 12:M, 13:C, 14:PM, 15:PC, 16:MBk1, 17:MBk2, 18:GY, 19:PGY, 1A:R, 1B:B, 1C:G
• Remedy: 1. Mount the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.)

• Code: 200A
• Display: Paper size not detected. Press Load/Eject and reload the paper. Paper size not detected. Reload paper. Paper size not detected. Press OK and reload the paper.
• Description: Paper size detection failure Cannot detect the paper width (poorly positioned paper).
• Remedy:

• Code: 200B
• Display: Paper size not detected. Reload paper.
• Description: Paper size detection failure Paper is invalidly positioned on the platen.
• Remedy:

• Code: 200C
• Display: Paper size not detected. Press Load/Eject and reload the paper. Paper size not detected. Reload paper. Paper size not detected. Lift the release lever and reload the paper.
• Description: Paper size detection failure Cannot detect the leading edge of the paper. The leading edge of paper has been located by coarse detection but not by a second round of fine detection (up to 300 mm) (semi-transparent paper).
• Remedy:

• Code: 200E
• Display: This paper cannot be used. Check supported paper sizes. This paper cannot be used. Check supported paper sizes. Load/Eject: Change Paper
• Description: Paper is too small The width and length of paper detected are shorter than the supported size (1.5% margin).
• Remedy: 1. Check paper conditions (soiling, tear-offs, residual paper chips, residual trimming cuts, folds)/size. 2. Has the paper been fed successfully (without slippage under a load or any influence)? 3. Has the LF adjustment value set correctly? 4. Hasn't the loaded paper shrunk to below its margin in the particular environment?