• Code: 553-8002-02
• Description: Error in the Lower Escape Delivery Shift Motor (Finisher-V1)
• Causes: The Lower Escape Delivery Roller HP Sensor does not detect the lower escape delivery roller when the Lower Escape Delivery Shift Motor has been driven for 1 second.
• Remedy: STAPLE FIN-V1/BOOKLET FIN-V1 [Related parts] - Harnesses from the Lower Escape Delivery Roller HP Sensor (PS112) to the Finisher Controller PCB - Harnesses from the Lower Escape Delivery Shift Motor (M106) to the Finisher Controller PCB - Lower Escape Delivery Roller HP Sensor (PS112) - Lower Escape Delivery Shift Motor (M106) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 553-8003-02
• Description: Error in the Upper Escape Delivery Shift Motor (Finisher-V1)
• Causes: The upper escape delivery roller does not come off the Upper Escape Delivery Roller HP Sensor when the Upper Escape Delivery Shift Motor has been driven for 1 second.
• Remedy: STAPLE FIN-V1/BOOKLET FIN-V1 [Related parts] - Harnesses from the Upper Escape Delivery Roller HP Sensor (PS134) to the Finisher Controller PCB - Harnesses from the Upper Escape Delivery Shift Motor (M119) to the Finisher Controller PCB - Upper Escape Delivery Roller HP Sensor (PS134) - Upper Escape Delivery Shift Motor (M119) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 553-8004-02
• Description: Error in the Upper Escape Delivery Shift Motor (Finisher-V1)
• Causes: The Upper Escape Delivery Roller HP Sensor does not detect the upper escape delivery roller when the Upper Escape Delivery Shift Motor has been driven for 1 second.
• Remedy: STAPLE FIN-V1/BOOKLET FIN-V1 [Related parts] - Harnesses from the Upper Escape Delivery Roller HP Sensor (PS134) to the Finisher Controller PCB - Harnesses from the Upper Escape Delivery Shift Motor (M119) to the Finisher Controller PCB - Upper Escape Delivery Roller HP Sensor (PS134) - Upper Escape Delivery Shift Motor (M119) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 553-8011-02
• Description: Error in the Flapper Motor (Finisher-V1)
• Causes: The flapper does not come off the Flapper HP Sensor when the Flapper Motor has been driven for 1 second.
• Remedy: STAPLE FIN-V1/BOOKLET FIN-V1 [Related parts] - Harnesses from the Flapper HP Sensor (PS105) to the Finisher Controller PCB - Harnesses from the Flapper Motor (M104) to the Finisher Controller PCB - Flapper HP Sensor (PS105) - Flapper Motor (M104) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 553-8012-02
• Description: Error in the Flapper Motor (Finisher-V1)
• Causes: The Flapper HP Sensor does not detect the flapper when the Flapper Motor has been driven for 1 second.
• Remedy: STAPLE FIN-V1/BOOKLET FIN-V1 [Related parts] - Harnesses from the Flapper HP Sensor (PS105) to the Finisher Controller PCB - Harnesses from the Flapper Motor (M104) to the Finisher Controller PCB - Flapper HP Sensor (PS105) - Flapper Motor (M104) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 553-8013-02
• Description: Error in the Escape Flapper Motor (Finisher-V1)
• Causes: The escape flapper does not come off the Escape Flapper HP Sensor when the Escape Flapper Motor has been driven for 1 second.
• Remedy: STAPLE FIN-V1/BOOKLET FIN-V1 [Related parts] - Harnesses from the Escape Flapper HP Sensor (PS132) to the Finisher Controller PCB - Harnesses from the Escape Flapper Motor (M118) to the Finisher Controller PCB - Escape Flapper HP Sensor (PS132) - Escape Flapper Motor (M118) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 553-8014-02
• Description: Error in the Escape Flapper Motor (Finisher-V1)
• Causes: The Escape Flapper HP Sensor does not detect the escape flapper when the Escape Flapper Motor has been driven for 1 second.
• Remedy: STAPLE FIN-V1/BOOKLET FIN-V1 [Related parts] - Harnesses from the Escape Flapper HP Sensor (PS132) to the Finisher Controller PCB - Harnesses from the Escape Flapper Motor (M118) to the Finisher Controller PCB - Escape Flapper HP Sensor (PS132) - Escape Flapper Motor (M118) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 553-80F1-02
• Description: Error in the Stack Delivery/Paddle Motor (Finisher-V1)
• Causes: The paddle does not come off the Paddle HP Sensor when the Stack Delivery/Paddle Motor has been driven for 1 second.
• Remedy: STAPLE FIN-V1/BOOKLET FIN-V1 [Related parts] - Harnesses from the Paddle HP Sensor (PS120) to the Finisher Controller PCB - Harnesses from the Stack Delivery/Paddle Motor (M103) to the Finisher Controller PCB - Paddle HP Sensor (PS120) - Stack Delivery/Paddle Motor (M103) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.