• Code: E575-0001
• Description: Gripper Unit Move Motor fails to move from HP
  At initial rotation, when the Motor rotates for specified period of time and cannot move from HP, it is detected as an error if the same symptom occurs again after the first retry.
• Remedy: 1. Check if the Motor (M2) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Gripper Unit HP Sensor (S7) Connector is physically removed. 4. Check if the Gripper Unit HP Sensor (S7) failure occurs.

• Code: E575-0002
• Description: Gripper Unit Move Motor fails to return to HP
  At initial rotation, when the Motor rotates for specified period of time and cannot return to HP, it is detected as an error if the same symptom occurs again after the first retry.
• Remedy: 1. Check if the Motor (M2) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Gripper Unit HP Sensor (S7) Connector is physically removed. 4. Check if the Gripper Unit HP Sensor (S7) failure occurs.

• Code: E584-0002
• Description: Shutter home position error
  The stapler does not return to the shutter home position when the stack ejection motor has been driven for 3 seconds.
• Remedy: 1. The shutter home position sensor (PI113) is faulty. 2. The shutter mechanism is faulty. 3. The stack ejection motor (M102), shutter clutch (CL101), ang stack ejection lower roller clutch (CL102) is faulty. 4. The finisher controller PCB is faulty.

• Code: E584-8001
• Description: Shutter home position error
  The stapler does not leave the shutter home position when the stack ejection motor has been driven for 30 seconds.
• Remedy: 1. The shutter home position sensor (PI113) is faulty. 2. The wiring between the finisher controller PCB and stack ejection motor, and between the finisher controller PCB and shutter clutch is faulty. 3. The shutter mechanism is faulty. 4. The stack ejection motor (M102), shutter clutch (CL101), ang stack ejection lower roller clutch (CL102) is faulty. 5. The finisher controller PCB is faulty.

• Code: E590-8001
• Description: Punch home position error
  The puncher does not detect the punch home position sensor when the puncher motor has been driven for 20 msec.
• Remedy: 1. The punch home position sensor (PI63) and punch motor clock sensor (PI62) is faulty. 2. The wiring between the punch controller PCB and sensor is faulty. 3. The punch mechanism is faulty. 4. The punch controller PCB is faulty. 5. The finisher controller PCB is faulty.

• Code: E590-8002
• Description: Punch home position error
  After the motor has been stopped at time of punch motor initialization, the puncher does not detect punch home position sensor.
• Remedy: 1. The punch home position sensor (PI63) and punch motor clock sensor (PI62) is faulty. 2. The wiring between the punch controller PCB and sensor is faulty. 3. The punch mechanism is faulty. 4. The punch controller PCB is faulty. 5. The finisher controller PCB is faulty.

• Code: E591-8001
• Description: Punch scrap empty error
  The voltage of the light received is 2.5 V or less even when the light emitting duty of the scrap full detector sensor has been increased to 66% or more.
• Remedy: 1. The wiring between the scrap full detector PCB and punch controller PCB is faulty. 2. The scrap full detector PCB is faulty. 3. The punch controller PCB is faulty. 4. The finisher controller PCB is faulty.

• Code: E591-8002
• Description: Punch scrap full detection error
  The voltage of the light received is 2.0 V or more even when the light emitting duty of the scrap full detector sensor has been decreased to 0%.
• Remedy: 1. The scrap full detector PCB is faulty. 2. The punch controller PCB is faulty. 3. The finisher controller PCB is faulty.