• Code: 514-8002-02
• Description: a. Error in the Gripper Base Motor (Finisher-X1) b. Error in the Paper End Assist Motor (Finisher-V)
• Causes: a. The Front Alignment HP Sensor does not detect the Front Alignment plate when the Front Alignment Motor has been driven for 3 seconds. b. The Paper End Assist HP Sensor does not detect the assist belt when the Paper End Assist Motor has been driven for 2 seconds.
• Remedy: a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Gripper Base Rear Sensor (S117) to the Finisher Controller PCB - Harnesses from the Gripper Base Motor (M116) to the Finisher Controller PCB - Gripper Base Rear Sensor (S117) - Gripper Base Motor (M116) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Paper End Assist HP Sensor (PS123) to the Finisher Controller PCB - Harnesses from the Paper End Assist Motor (M113) to the Finisher Controller PCB - Paper End Assist HP Sensor (PS123) - Paper End Assist Motor (M113) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 514-8003-02
• Description: Error in the Gripper Motor (Finisher-X1)
• Causes: The gripper does not come off the Gripper HP Sensor when the Gripper Motor has been driven for 3 seconds.
• Remedy: [Related parts] - Harnesses from the Gripper HP Sensor (S140) to the Finisher Controller PCB - Harnesses from theGripper Motor (M117) to the Finisher Controller PCB - Gripper HP Sensor (S140) - Gripper Motor (M117) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 514-8004-02
• Description: Error in the Gripper Motor (Finisher-X1)
• Causes: The Gripper HP Sensor does not detect the gripper when the Gripper Motor has been driven for 3 seconds.
• Remedy: [Related parts] - Harnesses from the Gripper HP Sensor (S140) to the Finisher Controller PCB - Harnesses from theGripper Motor (M117) to the Finisher Controller PCB - Gripper HP Sensor (S140) - Gripper Motor (M117) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 514-8005-02
• Description: Error in the Gripper Motor (Finisher-X1)
• Causes: The gripper does not come off the Position Sensor when the Gripper Motor has been driven for 3 seconds.
• Remedy: [Related parts] - Harnesses from the Gripper HP Sensor (S140) to the Finisher Controller PCB - Harnesses from theGripper Motor (M117) to the Finisher Controller PCB - Gripper HP Sensor (S140) - Gripper Motor (M117) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 514-8006-02
• Description: Error in the Gripper Motor (Finisher-X1)
• Causes: The Gripper Position Sensor does not detect the gripper when the Gripper Motor has been driven for 3 seconds.
• Remedy: [Related parts] - Harnesses from the Gripper Position Sensor (S115) to the Finisher Controller PCB - Harnesses from the Gripper Motor (M117) to the Finisher Controller PCB - Gripper Position Sensor (S115) - Gripper Motor (M117) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 518-8001-02
• Description: a. Error in the Fold Feed Motor (Paper Folding Unit-J1) b. Error in Fold Transport Motor (Document Insertion / Folding Unit-K1)
• Causes: a. A lock signal is continuous to detected for specific time after Folding Feed Motor drives. b. Fold Transport Motorr lock signal has been detected for more than the specified period of time.
• Remedy: a. Paper Folding Unit-J1 [Related parts] -Harnesses from the Paper Folding Unit Controller PCB to the Fold Feed Motor (M11) -Fold Feed Motor (M11) -Paper Folding Unit Controller PCB (PCB1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Paper Folding Unit Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. b. Document Insertion / Folding Unit-K1 [Related parts] - Harnesses from the Inserter/Folder ContRoller PCB (PCB2) to the Fold Transport Motor(M5) - Inserter/Folder ContRoller PCB (PCB2) - Fold Transport Motor(M5) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When replacing the Inserter/Folder ContRoller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 530-8000-02
• Description: Error in the Front or Rear Alignment Motor (Finisher-X1)
• Causes: The Front or Rear Alignment Motor operate abnormally during initialization.
• Remedy: [Related parts] - Harnesses from the Front/Rear Alignment HP Sensor (S108/S109) to the Finisher Controller PCB - Harnesses from the Front/Rear Alignment Motor (M108/M109) to the Finisher Controller PCB - Front/Rear Alignment HP Sensor (S108/S109) - Front/Rear Alignment Motor (M108/M109) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 530-8001-02
• Description: a. Error in the Front Alignment Motor (Finisher-X1) b. Error in the Front Alignment Motor (Finisher-V)
• Causes: a. The front alignment plate does not come off the Front Alignment HP Sensor when the Front Alignment Motor has been driven for 4 seconds. b. The front alignment plate does not come off the Front Alignment HP Sensor when the Front Alignment Motor has been driven for 1 second.
• Remedy: a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Front Alignment HP Sensor (S108) to the Finisher Controller PCB - Harnesses from the Front Alignment Motor (M108) to the Finisher Controller PCB - Front Alignment HP Sensor (S108) - Front Alignment Motor (M108) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Front Alignment HP Sensor (PS115) to the Finisher Controller PCB - Harnesses from the Front Alignment Motor (M107) to the Finisher Controller PCB - Front Alignment HP Sensor (PS115) - Front Alignment Motor (M107) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.