Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR Advance C7570i — Trang 19/112

Code: 061-0002-05

Description: Potential Sensor offset error
Causes: It was detected that the result of offset adjustment of the Potential Sensor was +/- 30 V or more.
Remedy: [Related parts] R1.00 - Harness between the Multi-purpose Tray Pickup Driver PCB (UN97/J1355) and the Potential Control PCB (UN29/J3530) - Harness between the Potential Control PCB (UN29/J3531) and the Potential Sensor (UN160/ J8073) - Potential Sensor (UN160) - Potential Control PCB (UN29) - Multi-purpose Tray Pickup Driver PCB (UN97) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the installation of the electrode for checking the Potential Sensor. 2. Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Potential Control PCB Unit, execute offset adjustment of the Potential Sensor by referring to "Parts Replacement and Cleaning Procedure> Image Formation System> Potential Sensor> When Replacing the Potential Control PCB" in the Service Manual.

Code: 061-0003-05

Description: Potential control dark area potential error
Causes: It was detected that the drum surface potential Vd measured at potential control ended upper/lower limit error against Vgrid.
Remedy: [Related parts] R1.00 - Harness between the Multi-purpose Tray Pickup Driver PCB (UN97/J1354) and the Cleaning Pre-exposure LED (Bk) (LED1/J7026) - Harness between the Laser Interface PCB (UN106/J76) and the Laser Scanner Unit (Bk) (J8064) - Cleaning Pre-exposure LED (Bk) (LED1) - Primary Charging Assembly - Laser Scanner Unit (Bk) - Multi-purpose Tray Pickup Driver PCB (UN97) - Laser Interface PCB (UN106) [Remedy] Check/replace the related harness/cable, connector and parts.

Code: 061-0004-05

Description: Potential control laser intensity error
Causes: It was detected that the potential difference of the laser power (LPW60h to LPWE0h) was 100 V or less when measuring VL at potential control.
Remedy: [Related parts] R1.00 - Harness between the Laser Interface PCB (UN106/J76) and the Laser Scanner Unit (Bk) (J8064) - Laser Scanner Unit (Bk) - Laser Interface PCB (UN106) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Clean the Dustproof Glass. 2. Check/replace the related harness/cable, connector and parts.

Code: 061-0005-05

Description: Cleaning Pre-exposure LED (Bk) activation error
Causes: It was detected that the drum surface potential was 350 V or less after charging high voltage was turned OFF at last rotation.
Remedy: [Related parts] R1.00 - Harness between the Multi-purpose Tray Pickup Driver PCB (UN97/J1354) and the Cleaning Pre-exposure LED (Bk) (LED1/J7026) - Cleaning Pre-exposure LED (Bk) (LED1) - Drum Unit (Bk) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Clean the Dustproof Glass. 2. Check/replace the related harness/cable, connector and parts.

Code: 064-1000-05

Description: Primary charging DC output error (CL)
Causes: Power supply of 24 V was detected while primary charging DC was being stopped.
Remedy: [Related parts] R1.00 - Harness between the Relay PCB (UN7/J1816) and the Primary Charging High Voltage PCB (CL) (UN38/J3021) - Harness between the DC Controller PCB (UN2/J1253) and the Primary Charging High Voltage PCB (CL) (UN38/J3040) - Primary Charging High Voltage PCB (CL) (UN38) - Relay PCB (UN7) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Code: 064-1001-05

Description: Developing DC output error (CL)
Causes: Power supply of 24 V was detected while developing DC was being stopped.
Remedy: [Related parts] R1.00 - Harness between the Relay PCB (UN7/J1816) and the Primary Charging High Voltage PCB (CL) (UN38/J3021) - Harness between the Relay PCB (UN7/J1808) and the Developing High Voltage PCB (CL) (UN40/J3041) - Harness between the DC Controller PCB (UN2/J1253) and the Primary Charging High Voltage PCB (CL) (UN38/J3040) - Primary Charging High Voltage PCB (CL) (UN38) - Relay PCB (UN7) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Code: 064-1100-05

Description: Primary charging AC bias (Y) high voltage output error
Causes: It was detected that the output value of the primary charging AC bias (Y) was out of the specified range.
Remedy: [Related parts] R1.00 - Cable between the Primary Charging High Voltage PCB (CL) (UN38/J3022) and the Resistance PCB (UN59) - Resistance PCB (UN59) - Primary Charging High Voltage PCB (CL) (UN38) [Remedy] Check/replace the related harness/cable, connector and parts.

Code: 064-1101-05

Description: Primary charging AC (Y) high voltage output error
Causes: It was detected that the output value of the primary charging AC (Y) was out of the specified range at open detection.
Remedy: [Related parts] R1.00 - Cable between the Primary Charging High Voltage PCB (CL) (UN38/J3022) and the Resistance PCB (UN59) - Resistance PCB (UN59) - Primary Charging High Voltage PCB (CL) (UN38) [Remedy] Check/replace the related harness/cable, connector and parts.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie