Causes: It was detected that amplitude of the Toner Density Sensor in the Developing Assembly (C) was the specified value or lower.
Remedy: [Related parts] - Drive section of the Developing Stirring Motor Unit (Developing Coupling (Small), Developing Coupling Joint, Developing Coupling Gear, Screw A Gear in the Developing Assembly) - Developing Stirring Motor Unit [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Open the Front Inner Door Unit, and check the drive section of the Developing Stirring Motor Unit. If engagement is poor, rotate the gears and adjust the engagement. 2. Replace the Developing Stirring Motor Unit.
Code: 023-0401-05
Description: Developing Stirring Motor (Bk) error
Causes: The lock signal of the Developing Stirring Motor (Bk) could not be detected within the specified period of time.
Remedy: [Related parts] R1.00 - Harnesses connecting the Side Driver PCB (UN96/J1303), the Drawer Unit (J8031) and the Developing Stirring Motor (Bk) (M29/J7152) - Developing Stirring Motor (Bk) (M29) - Developing Assembly (Bk) - Side Driver PCB (UN96) [Remedy] Check/replace the related harness/cable, connector and parts.
Code: 023-0402-05
Description: Developing Stirring Motor (Bk) error
Causes: The Developing Stirring Motor (Bk) was unlocked although it had been locked once.
Remedy: [Related parts] R1.00 - Harnesses connecting the Side Driver PCB (UN96/J1303), the Drawer Unit (J8031) and the Developing Stirring Motor (Bk) (M29/J7152) - Developing Stirring Motor (Bk) (M29) - Developing Assembly (Bk) - Side Driver PCB (UN96) [Remedy] Check/replace the related harness/cable, connector and parts.
Causes: It was detected that amplitude of the Toner Density Sensor in the Developing Assembly (Bk) was the specified value or lower.
Remedy: [Related parts] - Drive section of the Developing Stirring Motor Unit (Developing Coupling (Small), Developing Coupling Joint, Developing Coupling Gear, Screw A Gear in the Developing Assembly) - Developing Stirring Motor Unit [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Open the Front Inner Door Unit, and check the drive section of the Developing Stirring Motor Unit. If engagement is poor, rotate the gears and adjust the engagement. 2. Replace the Developing Stirring Motor Unit.
Causes: The Toner Feed Screw Rotation Sensor (Y) did not detect rotation of the screw within the specified period of time.
Remedy: [Related parts] R1.00 - Harness between the DC Controller PCB (UN2/J1247) and the Toner Feed Screw Rotation Sensor (Y) (PS12/J7418) - Harness between the DC Controller PCB (UN2/J1247) and the Hopper and Stirring Supply Motor (Y) (M9/J7100) - Toner Feed Screw Rotation Sensor (Y) (PS12) - Hopper and Stirring Supply Motor (Y) (M9) - Hopper Unit (Y) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Toner Feed Screw Rotation Sensor (Y) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
Code: 025-0110-05
Description: Toner Container reciprocation HP timeout error (Y)
Causes: The Toner Container Reciprocation HP Sensor (Y) did not detect home position within the specified period of time.
Remedy: [Related parts] R1.00 - Harness between the DC Controller PCB (UN2/J1247) and the Toner Container Drive Motor (Y) (M10/J7100) - Harness between the DC Controller PCB (UN2/J1249) and the Toner Container Reciprocation HP Sensor (Y) (PS11/J1990) - Toner Container Drive Motor (Y) (M10) - Toner Container Reciprocation HP Sensor (Y) (PS11) - Hopper Unit (Y) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. 1. If the Toner Container Reciprocation HP Sensor (Y) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
Causes: The Toner Container Replacement Door Sensor (Y) detected the open state while the Toner Container Cap was open.
Remedy: [Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1310) and the Toner Container Replacement Door Sensor (Y) (PS10/J7122) - Harness between the DC Controller PCB (UN2/J1247) and the Toner Container Phase Sensor (Y) (PS81/J7123) - Toner Container Replacement Door Sensor (Y) (PS10) - Toner Container Phase Sensor (Y) (PS81) - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Toner Container Replacement Door is closed. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
Code: 025-0150-05
Description: Toner Density Sensor (Y) output lower limit error
Causes: The Toner Density Sensor (Y) detected that the output (Vsig_ind) was 51 or less 10 consecutive times.
Remedy: [Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1305) and the Toner Density Sensor (Y) (TS2/ J8944) - Harness between the DC Controller PCB (UN2/J1247) and the Hopper and Stirring Supply Motor (Y) (M9/J7104) - Toner Density Sensor (Y) (TS2) - Hopper and Stirring Supply Motor (Y) (M9) - Hopper Unit (Y) - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
Máy Photocopy
Máy in mã vạch - In tem nhãn
PC- Laptop - Điện thoại
Máy in – Mực in
Máy chiếu - Màn chiếu
Máy chấm công - Kiểm soát ra vào
Máy hủy tài liệu
Máy đếm tiền, kho , quỹ
Loa - Loa bluetooth, vi tính, Karaok
Máy lạnh, Cây nước nóng lạnh
