Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Epson AcuLaser C4000 — Trang 3/4

Code: 1200, 1210

Description: 1200 EEPROM write error 1210 EEPROM write count limit
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2. 2 Checking the EEPROM: • “Error C1200”... Execute “SelecType Init” in the Panel Setting, or replace EEPROM. • “Error C1210”...Replace EEPROM. In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved.

Code: 1400

Description: Engine initialization malfunction
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. • With the tool: Go to step 2. • Without the tool: Go to step3. 2 Initializing the MCU PWB: • By using the DIAG command, execute “Slave Initialize”. Turn the power off once and on again. Does the printer operate normally? Problem solved. Go to step 3. 3 Replacing the relevant unit: • Replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved.

Code: 1500

Description: CCNV hardware error
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2. 2 Replacing the IC concerned: • Replace IC601 (VIP2: E05B93BA). • Replace IC600 (PWM). In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved.

Code: 1550

Description: Compression SRAM initialization hardware error
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2. 2 Checking the SD-RAM: • Remove all SD-RAMs from the RAM slots and then reinsert them in the RAM slots. Be sure to insert the SD-RAMs one by one (S0 and S1) in order so that the SD-RAM error can be identified. Every time you insert an SD-RAM, follow the procedures below and repeat it for each one. 1. Turn the power off. 2. Add the SD-RAM. 3. Turn the power on. • Insert the SD-RAM in the socket until it is locked securely. NOTE: Since the SD-RAM has the right direction to insert, be sure to insert it in the correct direction. Replace or reinstall the relevant part. Go to step 3. 3 Replacing the IC concerned: • Replace IC601 (VIP2: E05B93BA). • Replace IC600 (PWM). In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved.

Code: 1600

Description: Video related hardware error (including PWM IC calibration error)
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 Replacing the IC concerned: • Replace IC601 (VIP2: E05B93BA). • Replace IC600 (PWM). In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved.

Code: 1700

Description: Built-in network hardware error
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2. 2 Checking the network setting • Check if the existing network is operating normally. • Print the network status sheet to check if the every setting is correct. • Check if the network environment of the client side is correct. Problem solved. Go to step 3. 3 Replacing the relevant unit: Replacing the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved.

Code: 1800

Description: DIMM SPD error
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2. 2 Replacing CODE ROM (C309PROG): • Replace the mounted CODE ROM with another one for checking. Replace the CONTROLLER PWB. Problem solved.

Code: 1999

Description: Other hardware error
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. • With the tool: Go to step 2. • Without the tool: Go to step3. 2 Initializing the MCU PWB: • By using the DIAG command, execute “Slave Initialize”. Turn the power off once and on again. Does the printer operate normally? Problem solved. Go to step 3. 3 Replacing the relevant unit: • Replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie