Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Epson AcuLaser C8600 — Trang 2/7

Code: 1120 ... 1123

Description: 1120 ROM checksum error (bit 0 ~ 7) 1121 ROM checksum error (bit 8 ~ 15) 1122 ROM checksum error (bit 16 ~ 23) 1123 ROM checksum error (bit 24 ~ 31)
Remedy: 1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • CODE ROM(C309PROG)ÇÃåšä² • Replace the mounted CODE ROM with another one for checking. Replace the CONTROLLER PWB. Go to step 3 3 • Clearing/updating the Program: • Clear the installed DIMM forcibly and update the program to the latest one in the DIMM. • Clear the new DIMM forcibly and update the program in the DIMM. Replace or reinstall the relevant part. Problem solved

Code: 113

Description: Fuser Unit malfunction (No Fuser Unit)
Remedy: 1 • Initial checking: Is there any parts of wrong specifications used, improper mounting, damage, distortion, dirt, or adherence of foreign matter? • Major parts to be checked: FUSER ASSY, MCU PWB, FUSER HARNESS ASSY, FUSER CONNECTOR Replace or reinstall the relevant part. Go to step 2 2 • Checking whether the problem lies in engine or controller: Can a test print (single sheet / consecutive printing, about 10 sheets each) be performed normally with the engine alone? Check the Printer Controller. (If an error still occurs after replacing, go to step 3.)] Go to step 3 3 • Checking for proper mounting of FUSER ASSY: Is the FUSER ASSY properly mounted? • Check by removing and reinstalling the FUSER ASSY. • With the tool: Go to step 4 • Without the tool: Go to step 5 Replace the faulty part(s). 4 • Checking the FUSER ASSY detection circuit: Is the FUSER ASSY detection circuit functioning properly? . By using the diagnostics commander, check by Digital Input Test device code "4B". Go to step 5 Replace the MCU PWB-XL 5 • Checking the power supply to FUSER ASSY detection circuit: Is the voltage 5 VDC between P19B-5PIN . P19B-6PIN? Go to step 6 Replace the MCU PWB-XL 6 • Checking the FUSER ASSY detection signal Is the voltage between P/J19A-8PIN . P/J19A- 7PIN 0 VDC with the FUSER ASSY installed and 5 VDC without FUSER ASSY? Replace the MCU PWB-XL Go to step 7 7 • Checking for continuity of FUSER HARNESS ASSY Is there normal continuity between J71A . J78? Go to step 8 Replace the FUSER HARNESS ASSY 8 • Checking continuity of FUSER CONNECTOR Is there normal continuity between P71 . J19? Go to step 9 Replace the FUSER CONNECTOR 9 • Replacing the FUSER ASSY and Performing Checks Replace the FUSER ASSY. Is the problem solved? Problem solved Replace the MCU PWB-XL

Code: 1180 ... 1185

Description: 1180 Optional ROM module A checksum error *Only AcuLaser C8600 1181 Optional ROM module B checksum error *Only AcuLaser C8600 1185 Unsupported ROM module *Only AcuLaser C8600
Remedy: 1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • Checking the DIMM: • Insert the DIMM in the socket until it is locked securely. NOTE: Since the DIMM has the right direction and location for insertion, be sure to insert it in the correct direction and location. • Check if the DIMM is available for this printer, AcuLaser C8600. In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved

Code: 1200, 1210

Description: 1200 EEPROM write error 1210 EEPROM write count limit
Remedy: 1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • Checking the EEPROM: • “Error C1200”... Execute “SelecType Init” in the Panel Setting, or replace EEPROM. • “Error C1210”...Replace EEPROM. In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved

Code: 1400

Description: Engine initialization malfunction
Remedy: 1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • Initializing the MCU PWB: • By using the DIAG command, execute “Slave Initialize”. Turn the power off once and on again. Does the printer operate normally? Problem solved Go to step 3 3 • Replacing the relevant unit: • Replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved

Code: 1500

Description: CCNV hardware error
Remedy: 1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • Replacing the IC concerned: • Replace IC603 for AcuLaser C8600 or IC600 for AcuLaser C7000 (VIPS: E05B93BA) • Replace IC602 for AcuLaser C8600 or IC601 for AcuLaser C7000 In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved

Code: 1550

Description: Compression SRAM initialization hardware error
Remedy: 1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • Checking the SD-RAM: • Remove all SD-RAMs from the RAM slots and then reinsert them in the RAM slots. Be sure to insert the SD-RAMs one by one (S0 and S1) in order so that the SD-RAM error can be identified. Every time you insert an SD-RAM, follow the procedures below and repeat it for each one. 1 Turn the power off. 2 Add the SD-RAM. 3 Turn the power on. • Insert the SD-RAM in the socket until it is locked securely. NOTE: Since the SD-RAM has the right direction to insert, be sure to insert it in the correct direction. Replace or reinstall the relevant part. Go to step 3 3 • Replacing the IC concerned: • Replace IC603 for AcuLaser C8600 or IC600 for AcuLaser C7000 (VIPS: E05B93BA) • Replace IC602 for AcuLaser C8600 or IC601 for AcuLaser C7000 In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved

Code: 1600

Description: Video related hardware error (including PWM IC calibration error)
Remedy: 1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • Replacing the IC concerned: • Replace IC603 for AcuLaser C8600 or IC600 for AcuLaser C7000 (VIPS: E05B93BA) • Replace IC602 for AcuLaser C8600 or IC601 for AcuLaser C7000 In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie