Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP DesignJet T730 Printer

Code: 0000-0059

Description: 00.00. Unknown Service Part
Causes: 59. MOTOR_SERVO_SHUTDOWN
Remedy:

Code: 0001-0082

Description: Real Time Clock (RTC) Battery ran down.
Causes:
Remedy: How to solve. Remote troubleshooting (call agent) 1. The call agent asks the customer to go to the Support Menu by pressing the Power key continuously for 15 seconds. 2. Go to the Diagnostics Menu and select RTC Battery Status to check whether the RTC Battery has actually expired. 3. If yes, the call agent should arrange a service engineer visit to replace the RTC battery by replacing the Main PCA. Main PCA Onsite troubleshooting and solution (service engineer)1. Replace the Main PCA, see Main PCA. 2. Switch on the printer and go to Extended Support Menu Extended Support Menu. Select RTC Battery Expired option from the Reset Menu in order to reset the RTC battery expired flag.3. Go back and select Set Date and Time from the Service Menu Set the correct date and time.

Code: 0004-0001

Description: Printer Bundle Board communication failure or malfunction
Causes: Bundle FFC, Main PCA
Remedy: How to solve. Remote troubleshooting (call agent)1. Switch the power off and disconnect the power cord. Reconnect the power cord and power on the printer.2. The call agent should arrange a service engineer visit to change the Bundle PCA and follow steps below on Onsite Troubleshooting: Printer Bundle Board3. If a different system error is displayed then the call agent should perform the applicable troubleshooting procedure.Onsite troubleshooting and solution (service engineer)1. Remove covers and check that all the cables in the Bundle PCA and associated parts are correctly connected, and that none of them is damaged. If any cable is disconnected then reconnect it, and power on the printer again to check whether the system error has disappeared. Important note: If any cable is damaged then order a Cable Service Kit: Cables Sk2. Replace the Bundle PCA, see Bundle Board. Printer Bundle Board3. Replace the Bundle FFC cable, see Bundle Board FFC cable. 4. Replace the Main PCA (MPCA See Main PCA)

Code: 0008-0001

Description: Front Panel does not respond
Causes:
Remedy: Onsite troubleshooting and solution (service engineer)1. This error never appears in the Front Panel, it is only logged into the Error History, and is equivalent to the 3 beeps during printer startup.2. It happens when there is no communication between the Front Panel and the Main PCA, see Printer shows Resuming Screen during OOBE.

Code: 0009-0101

Description: Scanner Bundle Board PCA
Causes: Main PCA
Remedy: Remote troubleshooting (call agent)1. Switch the power off and disconnect the power cord. Reconnect the power cord and power on the printer.2. The call agent should arrange a service engineer visit to change the Scanner Bundle PCA, and follow the Onsite troubleshooting below: Scanner Bundle Board. Board3. If a different system error is displayed then the call agent should perform the applicable troubleshooting procedure.Onsite troubleshooting and solution (service engineer)1. Remove covers and check that the cables in the Scanner Bundle PCA and associated parts are correctly connected and not damaged. If any cable is disconnected then reconnect it, and power on the printer again to check whether the system error has disappeared. IMPORTANT: If any cable is damaged then order the appropriate Service Kit: Cables and Sensors 2. Replace the Scanner Bundle PCA, see Scan Bundle Board F9A30-67029. 3. Replace the Main PCA (MPCA See Main PCA)

Code: 0009-0174

Description: Scanner bundle PCA Non-volatile memory issue
Causes:
Remedy: Remote troubleshooting (call agent)1. Switch the unit off and on again.2. If the problem persist, go to the Extended support menu and use the saved Scanner calibrations.Onsite troubleshooting and solution (service engineer) Ensure the Main and Scan Bundle Board are properly connected, or replace Scan Bundle Board.

Code: 0009-0201

Description: Scanner Motor failure
Causes: Motor, transmission, pinches, or advance rollers
Remedy: Remote troubleshooting (call agent)1. Switch the power off and disconnect the power cord. Reconnect the power cord and power on the printer.2. Enter the support menu, see Entering the support menus, and run the Scanner Media Drive diagnostics test.3. Depending on the result, the call agent should arrange a service engineer visit to change the scanner motor and transmission, or any of the service parts involved on the media drive.Onsite troubleshooting and solution (service engineer)1. Replace the scanner motor and transmission.2. Ensure the pinches and advance rollers turn freely, and the transmission to the sliders works properly.3. Run the Scanner Media Drive diagnostics test to ensure the system works properly after the repair.

Code: 0009-0301

Description: Scanbar failure
Causes:
Remedy: Remote troubleshooting (call agent)1. Switch the power off and disconnect the power cord. Reconnect the power cord and power on the printer. If the error persist, the call agent should arrange a service engineer visit.2. Print the scanner diagnostic plot or calibrate it.3. Scan it and check the result.Onsite troubleshooting and solution (service engineer)1. Check the Scanbar connections to the main PCA.2. Replace the Scanbars set, see Scanbars F9A30-67017 (HP DesignJet T830 MFP only). NOTE:Please remember all 3 scanbars, together with the 3 white calibration surfaces, need to be replaced.3. Print the scanner calibration plot and calibrate them.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie