• Code: C0212
• Description: LCT ejection failure
  • The drawer cannot be determined to be out of position even after the set period of time has elapsed after the tray lock solenoid (SD51) is energized after the lowering operation is finished.
• Remedy: 1 Check the connector between SD51- PCCB51 PJ7 for proper connection and correct as necessary. 2 SD51 operation check 3 Change PCCB51.

• Code: C0213
• Description: LCT shift gate malfunction
  • The division board position sensor (PS5E) cannot be set to L even after the set period of time has elapsed after the operation of the division board position motor (M53) began with the division board position sensor (PS5E) set to L.
• Remedy: 1 Check the connector between PS5EPCREYB CN2<B> for proper connection and correct as necessary. 2 Check the connector between M53- PCREYB CN2<B> for proper connection and correct as necessary. 3 Check the connector of M53 for proper drive coupling, and correct as necessary. 4 PS5E I/O check, sensor check. 5 M53 operation check. 6 Change PCCB51.

• Code: C0214
• Description: LCT shifting failure
  • The shifter stop position sensor (PS5B) is not blocked even after the set period of time has elapsed after the shift operation began (shift to the right). • The shifter stop position sensor (PS5B) is not blocked even after the set pulse is detected by the shift motor sensor (PS58) after the shift operation began (shift to the right). • The shifter home position sensor (PS5C) is not unblocked even after the set pulse is detected by the shift motor pulse sensor (PS58) after the shift operation began (shift to the right). • The shifter home position sensor (PS5C) is not blocked even after the set period of time has elapsed after the return operation began (shift to the left). • The shifter home position sensor (PS5C) is not blocked even after the set pulse is detected by the shift motor pulse sensor (PS58) after the return operation began (shift to the left). • The shifter stop position sensor (PS5B) is not unblocked even after the set pulse is detected by the shift motor pulse sensor (PS58) after the return operation began (shift to the left).
• Remedy: 1 Check the connector between PS58- PCREYB CN2<A> for proper connection and correct as necessary. 2 Check the connector between PS5BPCREYB CN2<A> for proper connection and correct as necessary. 3 Check the connector between PS5CPCREYB CN2<A> for proper connection and correct as necessary. 4 PS58 I/O check, sensor check. 5 PS5B I/O check, sensor check. 6 PS5C I/O check, sensor check. 7 Change PCCB51.

• Code: C0215
• Description: LCT shift motor malfunction
  • The shift motor sensor (PS58) cannot detect both edges of H/L even after the set period of time has elapsed while the shift motor (M54) is turning backward/forward (raise/ lower)
• Remedy: 1 Check the connector between M54- PCREYB CN2<B> for proper connection and correct as necessary. 2 Check the connector between PS58- PCREYB CN2<A> for proper connection and correct as necessary. 3 Check the connector of M54 for proper drive coupling, and correct as necessary. 4 PS58 I/O check, sensor check. 5 M54 operation check. 6 Change PCCB51.

• Code: C1004
• Description: FNS communication error
  • When the FS control board (FSCB) is receiving data, a communication error is detected.
• Remedy: 1 Disconnect and then connect the power cord. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 2 Rewrite the firmware. 3 JSCB F1 conduction check. 4 JSCB F2 conduction check. 5 Change FSCB.

• Code: C1081
• Description: SD communication error
  • When a communication error is detected between the FS control board (FSCB) and the SD control board (SDCB).
• Remedy: 1 Disconnect and then connect the power cord. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 2 Rewrite the firmware. 3 Change SDDB. 4 Change FSCB.

• Code: C1113
• Description: Center-staple lead edge stopper motor malfunction
  <When FS-527+SD-509 is installed> • The leading edge stopper home sensor (PS45) is turned neither ON nor OFF even after the set period of time has elapsed after the leading edge stopper motor (M20) is turned ON.
• Remedy: 1 Check the connector between M20-SDDB PJ8 for proper connection and correct as necessary. 2 Check the connector between PS45-SDDB PJ10 for proper connection and correct as necessary. 3 Check the connector of M20 for proper drive coupling, and correct as necessary. 4 PS45 I/O check, sensor check. 5 M20 operation check. 6 Change M20. 7 Change SDDB. 8 Change FSCB.

• Code: C1114
• Description: Center-staple front adjust drive motor malfunction
  <When FS-527+SD-509 is installed> • The center staple alignment home sensor/F (PS42) is turned neither ON nor OFF even after the set period of time has elapsed after the center staple alignment motor/F (M24) is turned ON.
• Remedy: 1 Check the connector between M24-SDDB PJ7 for proper connection and correct as necessary. 2 Check the connector between PS42-SDDB PJ9 for proper connection and correct as necessary. 3 Check the connector of M24 for proper drive coupling, and correct as necessary. 4 PS42 I/O check, sensor check. 5 M24 operation check. 6 Change M24. 7 Change SDDB. 8 Change FSCB.