Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub 950 pro — Trang 2/35

Code: C-0022

Description: Initial communication check between the ADU drive board (ADUDB)/ printer control board (PRCB). ADU drive serial input abnormality 3. Within a specified period of time after the ACK at the time of the main power switch (SW1) being turned ON, a serial data from ID = 9 of the ADUDB is not received.
Causes: Confirmation of the wiring harness and the connector ADU drive board (ADUDB) Printer control board (PRCB)

Code: C-0101

Description: An abnormal speed signal of the paper feed motor (M4) is checked. An error detection signal is detected twice in succession a specified period of time after M4 was turned ON (the first signal is ignored).
Causes: Confirmation of the wiring harness and the connector Paper feed motor (M4) Printer control board (PRCB)

Code: C-0102

Description: An abnormal speed signal of the paper feed motor (M101) is checked. An error detection signal is detected twice in succession a specified period of time after M101 was turned ON (the first signal is ignored).
Causes: Confirmation of the wiring harness and the connector Paper feed motor (M101) Printer control board (PRCB)

Code: C-0104

Description: The 24V power source for SD/CL in the printer control board (PRCB) is checked. At the start, an error detection signal (blowout of ICP for the solenoid/clutch) is detected, and an error detection signal (24V cut off) is also detected.
Causes: Confirmation of the wiring harness and the connector Wiring harness earth fault Printer control board (PRCB) DC power supply /2 (DCPS2)

Code: C-0105

Description: The blowout of ICP for the SD/CL in the printer control board (PRCB) is checked. At the start, an error detection signal (blowout of ICP for the solenoid/clutch) is detected. However, an error detection signal (24V cut off) is not detected.
Causes: Loose connection (on PRCB) Solenoid (SD5 to SD10, SD4, SD11) Clutch (CL3 to CL8, CL9, CL10) Wiring harness earth fault Printer control board (PRCB)

Code: C-0210

Description: The locking of the paper lift motor /1 (M19) is detected. An error detection signal of M19 is detected while M19 is ON.
Causes: Tray 1 paper improperly loaded Tray 1 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /1 (M19) Upper limit sensor /1 (PS20) Printer control board (PRCB) DC power supply /2 (DCPS2)

Code: C-0211#

Description: When the upper limit sensor /1 (PS20) is OFF, PS20 does not turn ON within a specified period of time after the paper lift motor / 1 (M19) turns ON for lifting operation. And at this time, an error detection signal (24V cut off) is detected.
Causes: Tray 1 paper improperly loaded Tray 1 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /1 (M19) Upper limit sensor /1 (PS20) Printer control board (PRCB) DC power supply /2 (DCPS2)

Code: C-0212#

Description: When the upper limit sensor /1 (PS20) is OFF, PS20 does not turn ON within a specified period of time after the paper lift motor / 1 (M19) turns ON for lifting operation. At this time, an error detection signal (blowout of ICP) is detected.
Causes: Tray 1 paper improperly loaded Tray 1 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /1 (M19) Upper limit sensor /1 (PS20) Printer control board (PRCB) DC power supply /2 (DCPS2)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie