Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub C252P — Trang 9/13

Code: C3751

Description: Abnormal High Temp. (Heater)
• The temperatures of the Heating Roller Thermistor/1 (TH1) and the Heating Roller Thermistor/ 2 (TH3) are higher than a given level of degree for 1 second or more uninterruptedly. • The Heater Relay is OFF.
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-M. 5 Change PU1.

Code: C3752

Description: Abnormal High Temp. (Press)
• The temperature of the Fusing Pressure Roller Thermistor/1 (TH2) is higher than a given level of degree for 1 second or more uninterruptedly before the Heater temperature control starts. • The temperature of the Fusing Pressure Roller Thermistor/1 (TH2) is higher than a given level of degree for 1 second or more uninterruptedly after the Heater temperature control starts.
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-M. 5 Change PU1.

Code: C3851

Description: Abnormal Low Temp. (Heater)
• The temperature of the Heating Roller Thermistor/1 (TH1) is lower than a given level of degree for 1 second or more uninterruptedly during Ready mode, Low Power mode or printing. • The temperature of the Heating Roller Thermistor/2 (TH3) is lower than a given level of degree for 1 second or more uninterruptedly during Ready mode, Low Power mode or printing.
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-M. 5 Change PU1.

Code: C3852

Description: Abnormal Low Temp. (Press)
• The temperature of the Fusing Pressure Roller Thermistor /1 (TH2) is lower than a given level of degree for 1 second or more uninterruptedly during Ready mode, Low Power mode or printing.
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-M. 5 Change PU1.

Code: C3A01

Description: Paper Stuck to Fuser Heater Roller
• The temperature of the Heating Roller Thermistor /1 (TH1) goes down by a given level of degree compared to the temperature of a given period of time before when the paper passes on the Timing Roller and blocks the Exit Sensor (PC2).
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M for proper connection and correct or change as necessary. 3 PC2 I/O check, Sensor check PWB-M CNTH2-8 (ON) C-13. 4 Change Fusing Unit. 5 Change PWB-M. 6 Change PU1.

Code: C3A02

Description: Paper Stuck to Fuser Pressure Roller
• The temperature of the Fusing Pressure Roller Thermistor /1 (TH2) goes down by a given level of degree compared to the temperature of a given period of time before when the paper passes on the Timing Roller and blocks the Exit Sensor (PC2).
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M for proper connection and correct or change as necessary. 3 PC2 I/O check, Sensor check PWB-M CNTH2-8 (ON) C-13. 4 Change Fusing Unit. 5 Change PWB-M. 6 Change PU1.

Code: C4151

Description: Polygon Motor/C failure to turn
• The Polygon motor fails to turn stably even after the lapse of a given period of time after activating the Polygon motor.
• Motor Lock signal detects H for a given period time consecutively during the Polygon motor is rotating.
Remedy: 1 Check the connector for proper connection and correct as necessary. 2 Change PH Unit. 3 Change PWB-D. 4 Change PWB-M.

Code: C4152

Description: Polygon Motor/M failure to turn
Remedy: 1 Check the connector for proper connection and correct as necessary. 2 Change PH Unit. 3 Change PWB-D. 4 Change PWB-M.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie