• Code: C0206
• Description: Tray 3 lift-up failure (When PC-110 or PC-210 is installed) The tray 3 upper limit sensor (PS116) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
• Causes: • Tray 3 lift-up motor (M113) • Tray 3 upper limit sensor (PS116) • PC control board (PCCB) • MFP board (MFPB)
• Remedy: 1. Remove the tray and check to see if a piece of paper is not left inside the machine. 2. Check the connector between M113-PCCB CN6 for proper connection and correct as necessary. 3. Check the connector of M113 for proper drive coupling and correct as necessary. 4. Check the connector between PS116-relay CN24-PCCB CN4 for proper connection and correct as necessary. 5. PS116 I/O check, sensor check • Control signal: PCCB CN4-3 (ON) • Location of electrical component: PC-110/PC-210 7-C 6. M113 operation check • Control signal: PCCB CN6-8 to 9 • Location of electrical component: PC-110/PC-210 2-C 7. Replace M113. 8. Replace PCCB. 9. Replace MFPB.

• Code: C0208
• Description: Tray 4 lift-up failure (When PC-210 is installed). The tray 4 upper limit sensor (PS126) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
• Causes: • Tray 4 lift-up motor (M123) • Tray 4 upper limit sensor (PS126) • PC control board (PCCB) • MFP board (MFPB)
• Remedy: 1. Remove the tray and check to see if a piece of paper is not left inside the machine. 2. Check the connector between M123-PCCB CN8 for proper connection and correct as necessary. 3. Check the connector of M123 for proper drive coupling and correct as necessary. 4. Check the connector between PS126-relay CN47-PCCB CN7 for proper connection and correct as necessary. 5. PS126 I/O check, sensor check • Control signal: PCCB CN7-3 (ON) • Location of electrical component: PC-210 8-K 6. M123 operation check • Control signal: PCCB CN8-8 to 9 • Location of electrical component: PC-210 5-K 7. Replace M123. 8. Replace PCCB. 9. Replace MFPB.

• Code: C0210
• Description: LCC lift failure (When PC-410 is installed) • The main tray upper limit sensor (PS136) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began. • The shifter stop / lower limit position sensor (PS138) is not turned OFF (unblocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began. • The main tray upper limit sensor (PS136) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operating. • The main tray upper limit sensor (PS136) is not turned OFF (unblocked) even after the set period of time has elapsed after the paper lift-down operation began. • The shifter stop / lower limit position sensor (PS138) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-down operation began.
• Causes: • Main tray upper limit sensor (PS136) • Shifter stop / lower limit position sensor (PS138) • Elevator motor (M134) • PC control board (PCCB)
• Remedy: 1. Remove the tray and check to see if a piece of paper is not left inside the machine. 2. Check the connector between M134-PCCB CN10 for proper connection and correct as necessary. 3. Check the connector of M134 for proper drive coupling and correct as necessary. 4. Check the connector between PS136-relay CN1-PCCB CN4 for proper connection and correct as necessary. 5. Check the connector between PS138-relay CN16-PCCB CN14 for proper connection and correct as necessary. 6. PS136 I/O check, sensor check • Control signal: PCCB CN4-3 (ON) • Location of electrical component: PC-410 8-J 7. PS138 I/O check, sensor check • Control signal: PCCB CN14-6 (ON) • Location of electrical component: PC-410 3-J 8. M134 operation check • Control signal: PCCB CN10-1 to 2 • Location of electrical component: PC-410 6-J 9. Replace M134. 10. PRCB ICP2 conduction check 11. Replace PCCB.

• Code: C0211
• Description: Manual feed up/down abnormality. • Paper is not turned OFF (unblock) the bypass lift-up position sensor (PS26) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-up plate to the feed position. • The bypass lift-up position sensor (PS26) is not turned ON (blocked) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-up plate to the feed position.
• Causes: • Transport motor (M1) • Bypass pick-up solenoid (SD1) • Bypass lift-up position sensor (PS26) • MFP board (MFPB)
• Remedy: 1. Check the connector between M1-MFPB CN8E for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS26-relay CN19-MFPB CN18E for proper connection and correct as necessary. 4. Check the connector between SD1-relay CN21-relay CN19-MFPB CN18E for proper connection and correct as necessary. 5. PS26 I/O check, sensor check • Control signal: MFPB CN18E-13 (ON) • Location of electrical component: 22-J 6. SD1 operation check • Control signal: MFPB CN18E-10 (ON) • Location of electrical component: 22-J 7. M1 operation check • Control signal: MFPB CN8E-3 (REM), MFPB CN8E-6 (LOCK) • Location of electrical component: 2-C 8. Replace M1. 9. MFPB ICP3E conduction check 10. Replace MFPB.

• Code: C0214
• Description: LCC shift failure (When PC-410 is installed) • The shifter stop / lower limit position sensor (PS138) is not turned ON (blocked) even after the set period of time has elapsed after the shift operation began (shift to the right). • The shifter home sensor (PS139) is not turned OFF (unblocked) even after the set period of time has elapsed after the shift operation began (shift to the right). • The shifter stop / lower limit position sensor (PS138) is not turned OFF (unblocked) even after the set period of time has elapsed after the return operation began (shift to the left). • The shifter home sensor (PS139) is not turned ON (blocked) even after the set period of time has elapsed after the return operation began (shift to the left).
• Causes: • Shifter stop / lower limit position sensor (PS138) • Shifter home sensor (PS139) • Shifter motor (M133) • PC control board (PCCB)
• Remedy: 1. Remove the tray and check to see if a piece of paper is not left inside the machine. 2. Check the connector between M133-PCCB CN10 for proper connection and correct as necessary. 3. Check the connector of M133 for proper drive coupling and correct as necessary. 4. Check the connector between PS138-relay CN16-PCCB CN14 for proper connection and correct as necessary. 5. Check the connector between PS139-relay CN16-PCCB CN14 for proper connection and correct as necessary. 6. PS138 I/O check, sensor check • Control signal: PCCB CN14-6 (ON) • Location of electrical component: PC-410 3-J 7. PS139 I/O check, sensor check • Control signal: PCCB CN14-3 (ON) • Location of electrical component: PC-410 4-J 8. M133 operation check • Control signal: PCCB CN10-3 to 4 • Location of electrical component: PC-410 6-J 9. Replace M133. 10. PRCB ICP2 conduction check 11. Replace PCCB.

• Code: C0216
• Description: LCT up/down abnormality (When LU-302 is installed) The upper limit sensor (PS2) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
• Causes: • Upper limit sensor (PS2) • Lift-up motor (M1) • LU drive board (LUDB)
• Remedy: 1. Check the connector between M1-LUDB CN3 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-relay CN3-LUDB CN5 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: LUDB CN5-3 (ON) • Location of electrical component: LU-302 4-G 5. M1 operation check • Control signal: LUDB CN3-4 (ON) • Location of electrical component: LU-302 3-G 6. Replace M1. 7. Replace LUDB.

• Code: C1004
• Description: FNS communication error (When FS-533, FS-534, FS-534SD or JS-506 is installed) <When FS-533, FS-534 or FS-534SD is installed> • When the FS control board (FSCB) is receiving data, a communication error is detected. <When JS-506 is installed> • When the JS control board (JSCB) is receiving data, a communication error is detected.
• Causes: <When FS-533, FS-534 or FS-534SD is installed> • FS control board (FSCB) <When JS-506 is installed> • JS control board (JSCB)
• Remedy: When FS-533, FS-534 or FS-534SD is installed 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace FSCB. (FS-533/FS-534/FS-534SD) When JS-506 is installed 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace JSCB.

• Code: C1081
• Description: SD communication error (When FS-534SD is installed) When a communication error is detected between the FS control board (FSCB) and the SD control board (SDDB).
• Causes: • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace SDDB. 4. Replace FSCB.