Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub C654e — Trang 22/28

Code: CA053

Description: Controller start failure
A controller start failure is detected in the controller interface.
Causes: MFP board (MFPB)
Remedy: 1 Check to see if the following setting has been correctly made: [Service Mode] - [System 2] - [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Replace MFPB.

Code: CC001

Description: Vendor connection failure. It is detected that communications with the vendor are interrupted for a given period of time or more with "Installed" selected for the setting of vendor installation.
Causes: • Printer control board (PRCB) • Coin vendor (Japan) • Coin vendor kit (North America, Europe)
Remedy: 1 Check the vendor connector for proper connection and correct as necessary. - - 2 Check the PRCB connector for proper connection and correct as necessary. - - 3 Replace PRCB

Code: CC151

Description: ROM contents error upon startup (MSC). A fault is detected in a sequence of ROM contents check of the MFPB during starting
Causes:
Remedy: 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace the appropriate board.

Code: CC152

Description: ROM contents error upon startup (scanner). A fault is detected in a sequence of ROM contents check of the MFPB during starting
Causes:
Remedy: 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace the appropriate board.

Code: CC153

Description: ROM contents error upon startup (PRT). A fault is detected in a sequence of ROM contents check of the PRCB during starting.
Causes:
Remedy: 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace the appropriate board.

Code: CC155

Description: Finisher ROM error. Data of flash ROM of the finishing options is determined to be faulty when the power is turned ON.
Causes: FS control board (FSCB)
Remedy: 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace FSCB (FS-534/FS-535)

Code: CC156

Description: DF ROM error. Upgrade of the firmware has not been successful.
Causes: DF control board (DFCB)
Remedy: 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace DFCB

Code: CC157

Description: Finisher ROM error (ZU). Data of flash ROM of the z-folding unit is determined to be faulty when the power is turned ON.
Causes: ZU control board (ZUCB)
Remedy: 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace ZUCB
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie