• Code: C1196
• Description: Center fold roller motor’s malfunction
  <When FS-534+SD-511 is installed> The guide home sensor (PS7) is not blocked or unblocked even after the set period of time has elapsed after the center fold roller motor (M6) is turned ON.
• Causes: <When FS-534+SD-511 is installed> • Center fold roller motor (M8) • Guide home sensor (PS7) • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1 Check the connector between M8-SDDB J8 for proper connection, and correct as necessary. 2 Check the connector of M8 for proper drive coupling, and correct as necessary. 3 Check the connector between PS7-SDDB J9 for proper connection, and correct as necessary. 4 PS7 I/O check, sensor check SDDB J9-6 (ON) SD-511 4-G. 5 M8 operation check SDDB J8-11 to 14 SD-511 2 to 3-F to G. 6 Replace M8. 7 Replace SDDB. 8 Replace FSCB.

• Code: C1196
• Description: Tri-fold guide motor’s malfunction
  <When FS-535+SD-512 is installed> The tri-fold guide home sensor (PS7) is not not blocked or unblocked even after the set period of time has elapsed after the tri-fold guide motor (M6) is turned ON.
• Causes: <When FS-535+SD-512 is installed> • Tri-fold guide motor (M6) • Tri-fold guide home sensor (PS7) • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1 Check the connector between M6-SDDB J9 for proper connection, and correct as necessary. 2 Check the connector of M6 for proper drive coupling, and correct as necessary. 3 Check the connector between PS7-SDDB J9 for proper connection, and correct as necessary. 4 PS7 I/O check, sensor check SDDB J9-6 (ON) SD-512 4-G. 5 M6 operation check SDDB J9-7 to 10 SD-512 3-F to G. 6 Replace M6. 7 Replace SDDB. 8 Replace FSCB.

• Code: C1197
• Description: Tri-folding guide motor’s malfunction
  <When FS-534+SD-511 is installed> The tri-folding gate home sensor (PS11) is not blocked or unblocked even after the set period of time has elapsed while the tri-folding guide motor (M6) is energized
• Causes: <When FS-534+SD-511 is installed> • Tri-folding guide motor (M6) • Tri-folding gate home sensor (PS11) • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1 Check the connector between M6-SDDB J9 for proper connection, and correct as necessary. 2 Check the connector of M6 for proper drive coupling, and correct as necessary. 3 Check the connector between PS11-SDDB J8 for proper connection, and correct as necessary. 4 PS11 I/O check, sensor check SDDB J8-10 (ON) SD-511 3-G. 5 M6 operation check SDDB J9-7 to 10 SD-511 4-F to G. 6 Replace M6. 7 Replace SDDB. 8 Replace FSCB.

• Code: C1197
• Description: Center fold change motor’s malfunction
  <When FS-535+SD-512 is installed> The center fold change gate home sensor (PS11) is not blocked or unblocked even after the set period of time has elapsed while the center fold change motor (M8) is energized.
• Causes: <When FS-535+SD-512 is installed> • Center fold change motor (M8) • Center fold change gate home sensor (PS11) • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1 Check the connector between M8-SDDB J8 for proper connection, and correct as necessary. 2 Check the connector of M8 for proper drive coupling, and correct as necessary. 3 Check the connector between PS11-SDDB J8 for proper connection, and correct as necessary. 4 PS11 I/O check, sensor check SDDB J8-10 (ON) SD-512 2-G. 5 M8 operation check SDDB J8-11 to 14 SD-512 2-F to G. 6 Replace M8. 7 Replace SDDB. 8 Replace FSCB.

• Code: C11A2
• Description: Receiving roller pressure/ retraction motor’s malfunction
  <When FS-534 is installed> The receiving roller retraction sensor (PS11) is not blocked or unblocked even after the set period of time has elapsed after the receiving roller retraction motor (M4) is turned ON.
• Causes: • Receiving roller retraction motor (M4) • Receiving roller retraction sensor (PS11) • FS control board (FSCB)
• Remedy: 1 Check the connector between M4-FSCB J4 for proper connection, and correct as necessary. 2 Check the connector of M4 for proper drive coupling, and correct as necessary. 3 Check the connector between PS11-FSCB J4 for proper connection, and correct as necessary. 4 PS11 I/O check, sensor check FSCB J4<B>-16 (ON) FS-534 13-C. 5 M4 operation check FSCB J4<A>-1 to 4 FS-534 11-C to D. 6 Replace M4. 7 Replace FSCB.

• Code: C11C5
• Description: Paper size detect board failure
  <When FS-535+PK-521 is installed> The size of a transported paper is not detected, causing no punch operation.
• Causes:
• Remedy: 1 Check the sensor part of PSDTB, to clean if it is dirty. 2 Check the connector between PSDTB-PKCB CN38 for proper connection, and correct as necessary PK-521 4-E. 3 Replace PSDTB.

• Code: C11E1
• Description: Paper exit switching drive malfunction
  <When FS-534 is installed> The exchange folded paper output sensor (PS30) is not blocked or unblocked even after the set period of time has elapsed after the FNS entry transport motor (M2) is turned ON.
• Causes: • FNS entry transport motor (M2) • Exchange folded knife home position sensor (PS30) • FS control board (FSCB)
• Remedy: 1 Check the connector between M2-FSCB J9 for proper connection, and correct as necessary. 2 Check the connector of M2 for proper drive coupling, and correct as necessary. 3 Check the connector between PS30-FSCB J4 for proper connection, and correct as necessary. 4 PS30 I/O check, sensor check FSCB J4<A>-15 (ON) FS-534 12-C. 5 M2 operation check FSCB J9<A>-1 to 4 FS-534 10 to 11-B to C. 6 Replace M2. 7 Replace FSCB.

• Code: C2101
• Description: Charge cleaning motor/K’s malfunction
  During backward and return movement of the cleaner material, the charging cleaner home sensor is not blocked after a predetermined period of time has elapsed.
• Causes: • Drum unit /K • Charging cleaner home sensor (PS43) • Charging cleaner return sensor (PS44) • Charge cleaning motor/K (M15) • PH relay board (PHRYB) • Printer control board (PRCB)
• Remedy: 1 Check the drum unit for proper connection and correct as necessary. 2 Check the connector between M15-PHRYB CN12 for proper connection, and correct as necessary. 3 Check the M15 connector for proper connection and correct as necessary. 4 Check the connector between PS43-PHRYB CN2 for proper connection, and correct as necessary. 5 Check the connector between PS44-PHRYB CN2 for proper connection, and correct as necessary. 6 PS43 I/O check, sensor check PHRYB CN2-5 (ON) 10-B. 7 PS44 I/O check, sensor check PHRYB CN2-8 (ON) 11-B. 8 M15 operation check PHRYB CN12-1 to 2 9-B. 9 Replace drum unit. 10 Replace M15. 11 PHRYB ICP1 conduction check. 12 Replace PHRYB. 13 Replace PRCB.