Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub PRESS 1052 — Trang 47/94

Code: C-1235

Description: An error detection signal of M17 is detected continuously for a specified period of time while the main tray exit motor (M17) is ON.
Causes: • Main tray exit motor (M17) • Punch drive board (PDB)
Remedy: 1. Check the main tray exit section, and clean/repair it if any abnormality. 2. Check the connector connection and the wiring between PDB and the motor, and repair it if any abnormality. 3. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram: FD-503: 4-D) 4. Replace M17. 5. Replace PDB.

Code: C-1241

Description: The scraps press home sensor (PS48) does not turn ON within a specified period of time after the bundle exit motor (M5) starts the home position search operation.
Causes: • Bundle exit motor (M5) • Scraps press home sensor (PS48) • SD control board (SDCB) • SD drive board (SDDB) DIPSW7-0
Remedy: 1. Check the bundle exit section, and clean/repair it if any abnormality. 2. Check the connector connection and the wiring between SDDB and motor/sensor, and repair it if any abnormality. 3. Check the connector connection and the wiring between SDDB and SDCB, and repair it if any abnormality. 4. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 22-D) 5. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 24-D) 6. Replace PS48. 7. Replace M5. 8. Replace SDDB. 9. Replace SDCB.

Code: C-1242

Description: The folding main scan alignment home sensor / Fr1 (PS18) does not turn ON within a specified period of time after the folding main scan alignment motor /Fr (M7) starts the home position search operation. Or, even after a specified period of time after M7 starts the operation, it does not stop.
Causes: • Folding main scan alignment motor /Fr (M7) • Folding main scan alignment home sensor / Fr1 (PS18) • SD control board (SDCB) • SD drive board (SDDB) DIPSW7-0
Remedy: 1. Check the folding main scan alignment section, and clean/repair it if any abnormality. 2. Check the connector connection and the wiring between SDDB and motor/sensor, and repair it if any abnormality. 3. Check the connector connection and the wiring between SDDB and SDCB, and repair it if any abnormality. 4. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 8-D) 5. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 13-D) 6. Replace PS18. 7. Replace M7. 8. Replace SDDB. 9. Replace SDCB.

Code: C-1243

Description: The folding exit home sensor (PS24) does not turn ON within a specified period of time after the folding sub scan alignment exit motor (M8) starts the home position search operation. Or, even after a specified period of time after M8 starts to decelerate, it does not stop.
Causes: • Folding sub scan alignment exit motor (M8) • Folding exit home sensor (PS24) • SD control board (SDCB) • SD drive board (SDDB) DIPSW7-0
Remedy: 1. Check the folding sub scan alignment section, and clean/repair it if any abnormality. 2. Check the connector connection and the wiring between SDDB and motor/sensor, and repair it if any abnormality. 3. Check the connector connection and the wiring between SDDB and SDCB, and repair it if any abnormality. 4. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 10-D) 5. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 14-D) 6. Replace PS24. 7. Replace M8. 8. Replace SDDB. 9. Replace SDCB.

Code: C-1244

Description: The saddle stitching alignment home sensor /Rt (PS28) does not turn ON within a specified period of time after the saddle stitching alignment motor / Rt (M9) starts the home position search operation. Or, even after a specified period of time after M9 starts the operation, it does not stop.
Causes: • Saddle stitching alignment motor /Rt (M9) • Saddle stitching alignment home sensor / Rt (PS28) • SD control board (SDCB) • SD drive board (SDDB) DIPSW7-0
Remedy: 1. Check the saddle stitching alignment section, and clean/repair it if any abnormality. 2. Check the connector connection and the wiring between SDDB and motor/sensor, and repair it if any abnormality. 3. Check the connector connection and the wiring between SDDB and SDCB, and repair it if any abnormality. 4. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 19-D) 5. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 17-D) 6. Replace PS28. 7. Replace M9. 8. Replace SDDB. 9. Replace SDCB.

Code: C-1245

Description: The bundle arm home sensor (PS32) does not turn ON within a specified period of time after the bundle arm motor (M10) starts the home position search operation. Or, even after a specified period of time after M10 starts the operation, it does not stop.
Causes: • Bundle arm motor (M10) • Bundle arm home sensor (PS32) • SD control board (SDCB) • SD drive board (SDDB) DIPSW7-0
Remedy: 1. Check the bundle arm section, and clean/repair it if any abnormality. 2. Check the connector connection and the wiring between SDDB and motor/sensor, and repair it if any abnormality. 3. Check the connector connection and the wiring between SDDB and SDCB, and repair it if any abnormality. 4. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 19-D) 5. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 17-D) 6. Replace PS32. 7. Replace M10. 8. Replace SDDB. 9. Replace SDCB.

Code: C-1246

Description: The bundle clip upper limit sensor (PS33) does not turn ON within a specified period of time after the bundle clip motor (M11) starts the home position search operation. Or, even after a specified period of time after M11 starts the operation, it does not stop.
Causes: • Bundle clip motor (M11) • Bundle clip upper limit sensor (PS33) • Bundle clip lower limit sensor (PS30) • SD control board (SDCB) • SD drive board (SDDB) DIPSW7-0
Remedy: 1. Check the bundle clip section, and clean/repair it if any abnormality. 2. Check the connector connection and the wiring between SDDB and motor/sensor, and repair it if any abnormality. 3. Check the connector connection and the wiring between SDDB and SDCB, and repair it if any abnormality. 4. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram:SD-506:16-D) 5. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram:SD-506:19-D) 6. Replace PS33. 7. Replace M11. 8. Replace SDDB. 9. Replace SDCB.

Code: C-1247

Description: The bundle registration home sensor (PS34) does not turn ON within a specified period of time after the bundle registration motor (M12) starts the home position search operation. Or, even after a specified period of time after M12 starts the operation, it does not stop.
Causes: • Bundle registration motor (M12) • Bundle registration home sensor (PS34) • SD control board (SDCB) • SD drive board (SDDB) DIPSW7-0
Remedy: 1. Check the bundle registration section, and clean/repair it if any abnormality. 2. Check the connector connection and the wiring between SDDB and motor/sensor, and repair it if any abnormality. 3. Check the connector connection and the wiring between SDDB and SDCB, and repair it if any abnormality. 4. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 27-D) 5. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: SD-506: 21-D) 6. Replace PS34. 7. Replace M12. 8. Replace SDDB. 9. Replace SDCB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie