Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub Pro 1051 — Trang 44/91

Code: C-1230

Description: PI upper tray operation abnormality. After the FD paper lift motor /Up (M8) is in the down operation, the PI lift plate home sensor /Up (PS34) does not turn ON within a specified period of time. Or, after the paper lift motor /Up (M8) is in the up operation, the PI upper limit sensor /Up (PS32) does not turn ON. 33-3
Causes: PI upper limit sensor /Up (PS32: FD-503) PI lift plate home sensor /Up (PS34: FD-503) Paper lift motor /Up (M8: FD-503) PI drive board (PIDB: FD-503)
Remedy: 1 Check the PI upper tray section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between PIDB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FD-503: 9-A 4 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. FD-503: 8-A, 9-A 5 Replace PS32 or PS34. - 6 Replace M8. - 7 Replace PIDB.

Code: C-1231

Description: PI lower tray operation abnormality. After the FD paper lift motor /Lw (M9) is in the down operation, the PI lift plate home sensor /Lw (PS40) does not turn ON within a specified period of time. Or, after the paper lift motor /Lw (M9) is in the up operation, the PI upper limit sensor /Lw (PS38) does not turn ON. 33-3
Causes: PI upper limit sensor /Lw (PS38: FD-503) PI lift plate home sensor /Lw (PS40: FD-503) Paper lift motor /Lw (M9: FD-503) PI drive board (PIDB: FD-503)
Remedy: 1 Check the PI lower tray section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between PIDB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FD-503: 9-A 4 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. FD-503: 7-A, 8-A 5 Replace PS38 or PS40. - 6 Replace M9. - 7 Replace PIDB.

Code: C-1232

Description: Entrance conveyance motor (M1) rotation abnormality. M1 abnormality detection signal was continuously detected for the specified time when M1 was ON.
Causes: Entrance conveyance motor (M1: FD-503) Punch drive board (PDB: FD-503)
Remedy: 1 Check the entrance conveyance section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between PDB and the motor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FD-503: 3-D 4 Replace M1. - 5 Replace PDB.

Code: C-1233

Description: Intermediate conveyance motor (M3) rotation abnormality. M3 abnormality detection signal was continuously detected for the specified time when M3 was ON.
Causes: Intermediate conveyance motor (M3: FD-503) Punch drive board (PDB: FD-503)
Remedy: 1 Check the intermediate conveyance section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between PDB and the motor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FD-503: 4-D 4 Replace M3. - 5 Replace PDB.

Code: C-1234

Description: PI conveyance motor (M7) rotation abnormality. M7 abnormality detection signal was continuously detected for the specified time when M7 was ON. 33-3
Causes: PI conveyance motor (M7: FD-503) PI drive board (PIDB: FD-503)
Remedy: 1 Check the PI conveyance section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between PIDB and the motor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FD-503: 9-A 4 Replace M7. - 5 Replace PIDB.

Code: C-1235

Description: Main tray paper exit motor (M17) rotation abnormality. M17 abnormality detection signal was continuously detected for the specified time when M17 was ON.
Causes: Main tray exit motor (M17: FD-503) Punch drive board (PDB: FD-503)
Remedy: 1 Check the main tray exit section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between PDB and the motor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FD-503: 4-D 4 Replace M17. - 5 Replace PDB.

Code: C-1241

Description: Bundle exit drive motor (M5) drive abnormality. The scraps press home sensor (PS48) does not turn ON even after a specified period of time after M5 starts the home position search operation. 34-0/1/3
Causes: Scraps press home sensor (PS48: SD-506) Bundle exit motor (M5: SD-506) SD drive board (SDDB: SD-506) SD control board (SDCB: SD-506)
Remedy: 1 Check the bundle exit section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between SDDB and motor/sensor, and repair it if any abnormality. - 3 Check the connector connection and the wiring between SDDB and SDCB, and repair it if any abnormality. - 4 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. SD-506: 22-D 5 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. SD-506: 24-D 6 Replace PS48. - 7 Replace M5. - 8 Replace SDDB. - 9 Replace SDCB.

Code: C-1242

Description: Folding main scan alignment motor /Fr (M7) drive abnormality. The folding main scan alignment home sensor /Fr1 (PS18) does not turn ON even after a specified period of time after M7 starts the home position search operation. Or, even after a specified period of time after M7 starts the operation, it does not stop. 34-0/1/2/3
Causes: Folding main scan alignment home sensor /Fr1 (PS18: SD-506) Folding main scan alignment motor /Fr (M7: SD- 506) SD drive board (SDDB: SD-506) SD control board (SDCB: SD-506)
Remedy: 1 Check the folding main scan alignment section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between SDDB and motor/sensor, and repair it if any abnormality. - 3 Check the connector connection and the wiring between SDDB and SDCB, and repair it if any abnormality. - 4 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. SD-506: 8-D 5 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. SD-506: 13-D 6 Replace PS18. - 7 Replace M7. - 8 Replace SDDB. - 9 Replace SDCB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie