Description: The locking of the tray lift-up motor /1 (M25) is detected. An error detection signal of M25 is detected while M25 is ON.
Causes: Tray lift-up motor /1 (M25) Printer control board (PRCB)
Remedy: 1 Check the connector connection and the wiring between PRCB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 5-F 3 Replace M25. - 4 Replace PRCB.
Description: Tray /2 up abnormality 1. When the upper limit sensor /2 (PS10) is OFF, PS10 does not turn ON within 20seconds after the tray lift-up motor /2 (M34) turns ON for lifting operation. At this time, an error detection signal (24V cut off) is detected.
Causes: Upper limit sensor /2 (PS10) Tray lift-up motor /2 (M34) Printer control board (PRCB) DC power supply /2 (DCPS /2)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate condition of the tray 2, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 8-F 4 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. 6-G 5 Replace PS10. - 6 Replace M34. - 7 Replace PRCB. - 8 Replace DCPS /2.
Description: Tray /2 up abnormality 2. When the upper limit sensor /2 (PS10) is OFF, PS10 does not turn ON within 20seconds after the tray lift-up motor /2 (M34) turns ON for lifting operation. At this time, an error detection signal is not detected.
Causes: Upper limit sensor /2 (PS10) Tray lift-up motor /2 (M34) Printer control board (PRCB) DC power supply /2 (DCPS /2)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate condition of the tray 2, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 8-F 4 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. 6-G 5 Replace PS10. - 6 Replace M34. - 7 Replace PRCB. - 8 Replace DCPS /2.
Description: The locking of the tray lift-up motor /2 (M34) is detected. When M34 is ON, an error detection signal of the M34 is detected.
Causes: Tray lift-up motor /2 (M34) Printer control board (PRCB)
Remedy: 1 Check the connector connection and the wiring between PRCB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 8-F 3 Replace M34. - 4 Replace PRCB.
Description: 1st tandem PF-702/703 upper tray up abnormality. PF-702: When the upper limit sensor /1 (PS2) is OFF, PS2 does not turn ON within 20seconds after the paper lift motor /1 (M42) turns ON for lifting operation. PF-703: When the upper limit sensor /1 (PS5) is OFF, PS5 does not turn ON within 20seconds after the paper lift motor /1 (M7) turns ON for lifting operation. Or, the paper suction sensor /Fr1 and /Rr1 (PS25 and PS26) turn ON before PS5 turns ON while in tray lifting.
Causes: Upper limit sensor /1 (PS2: PF-702) Upper limit sensor /1 (PS5: PF-703) Paper lift motor /1 (M42: PF-702) Paper lift motor /1 (M7: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate misaligned of the upper tray, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PFUDB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 5-C PF-703: 6-F 4 Check I/O and the operation of the sensor, and repair it if any abnormality. PF-702: 3-C PF-703: 3-F 5 Replace PS2: PF-702 or PS5: PF-703. - 6 Replace M42: PF -702 or M7: PF-703. - 7 Replace PFUDB.
Description: The locking of the paper lift motor /1 of the 1st tandem PF-702/703 upper tray (M42: PF-702, M7: PF-703) is detected. When M42 and M7 are ON, error detection signals of the M42 and M7 are detected.
Causes: Paper lift motor /1 (M42: PF-702) Paper lift motor /1 (M7: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 5-C PF-703: 6-F 3 Replace M42: PF -702 or M7: PF-703. - 4 Replace PFUDB.
Description: 1st tandem PF-702/703 middle tray up abnormality. PF-702: When the upper limit sensor /2 (PS6) is OFF, PS6 does not turn ON within 20seconds after the paper lift motor /2 (M43) turns ON for lifting operation. PF-703: When the upper limit sensor /2 (PS9) is OFF, PS9 does not turn ON within 20seconds after the paper lift motor /2 (M8) turns ON for lifting operation. Or, the paper suction sensor /Fr2 and /Rr2 (PS27 and PS28) turn ON before PS9 turns ON while in tray lifting.
Causes: Upper limit sensor /2 (PS6: PF-702) Upper limit sensor /2 (PS9: PF-703) Paper lift motor /2 (M43: PF-702) Paper lift motor /2 (M8: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate misaligned of the middle tray, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PFUDB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 7-C PF-703: 12-F 4 Check I/O and the operation of the sensor, and repair it if any abnormality. PF-702: 5-C PF-703: 9-F 5 Replace PS6: PF-702 or PS9: PF-703. - 6 Replace M43: PF -702 or M8: PF-703. - 7 Replace PFUDB.
Description: The locking of the paper lift motor /2 of the 1st tandem PF-702/703 middle tray (M43: PF-702, M8: PF-703) is detected. When M43 and M8 are ON, error detection signals of the M43 and M8 are detected.
Causes: Paper lift motor /2 (M43: PF-702) Paper lift motor /2 (M8: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 7-C PF-703: 12-F 3 Replace M43: PF -702 or M8: PF-703. - 4 Replace PFUDB.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.