0

Các lỗi thường gặp

Code :
  • Code: C-0151
  • Description: The locking of the paper lift motor (M100) is detected. When M100 is ON, an error detection signal of the M100 is detected in succession for 1 second.
  • Causes: • Paper lift motor (M100) • Lower limit sensor (PS101) • Upper limit sensor (PS109) • LU drive board (LUDB) DIPSW47-0
  • Remedy: 1. Check the paper loaded condition and the rear end restriction plate misaligned of the tray, and repair it if any abnormality 2. Check the connector connection and the wiring between LUDB and motor/sensor, and repair it if any abnormality. 3. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: LU: 4-G, 6-G) 4. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram: LU: 5-C) 5. Replace PS109 and PS101. 6. Replace M100. 7. Replace LUDB.
  • Code: C-0152
  • Description: Abnormality of the paper lift motor (M100) power in the LU drive board (LUDB). An error detection signal (blowout of ICP) of M100 is detected.
  • Causes: • Paper lift motor (M100) • LU drive board (LUDB)
  • Remedy: 1. Check the connector connection and the wiring between LUDB and the motor, and repair it if any abnormality. 2. Check the I/O drive of the motor and the coupling of the gear, repair/replace it if any abnormality, and then replace M100 (Wiring diagram: LU: 5-C) 3. Replace LUDB. 4. Replace M100 and LUDB at a time.
  • Code: C-0153
  • Description: Abnormality of the solenoid and clutch power in the LU drive board (LUDB). An error detection signals (blowout of ICP) of the pick up solenoid (SD100), the paper feed clutch (CL101), and the preregistration clutch (CL102) are detected after the print is started.
  • Causes: • Pick-up solenoid (SD100) • Paper feed clutch (CL101) • Pre-registration clutch (CL102) • LU drive board (LUDB)
  • Remedy: 1. Check the connector connection and the wiring between LUDB and solenoid/clutch, and repair it if any abnormality. 2. Check the I/O drive of the solenoid/clutch and the coupling of the gear, repair/replace it if any abnormality, and then replace SD100, CL101 and CL102 (Wiring diagram: LU: 7-G, 6-G) 3. Replace LUDB. 4. Replace SD100/CL101/CL102 and LUDB at a time
  • Code: C-0201
  • Description: Tray1: up abnormality When the upper limit sensor /1 (PS6) is OFF, PS6 does not turn ON within 20 seconds after the tray lift-up motor /1 (M25) turns ON for lifting operation. At this time, an error detection signal (24V cut off) is detected.
  • Causes: • Upper limit sensor /1 (PS6) • Tray lift-up motor /1 (M25) • Printer control board (PRCB) • DC power supply /2 (DCPS/2) DIPSW18-0
  • Remedy: 1. Check the paper loaded condition and the rear end restriction plate condition of the tray1, and repair it if any abnormality 2. Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality 3. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram:Main body (3/4): 16-A) 4. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: Main body (2/4): 13-A) 5. Replace PS6 6. Replace M25 7. Replace PRCB. 8. Replace DCPS /2
  • Code: C-0203
  • Description: Tray1 up abnormality 2. When the upper limit sensor /1 (PS6) is OFF, PS6 does not turn ON within 20 seconds after the tray lift-up motor /1 (M25) turns ON for lifting operation. At this time, an error detection signal is not detected.
  • Causes: Upper limit sensor /1 (PS6) • Tray lift-up motor /1 (M25) • Printer control board (PRCB) • DC power supply /2 (DCPS/2) DIPSW18-0
  • Remedy: 1. Check the paper loaded condition and the rear end restriction plate condition of the tray1, and repair it if any abnormality 2. Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality 3. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram:Main body (3/4): 16-A) 4. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: Main body (3/4): 13-A) 5. Replace PS6 6. Replace M25 7. Replace PRCB. 8. Replace DCPS /2
  • Code: C-0204
  • Description: The locking of the tray liftup motor /1 (M25) is detected. An error detection signal of M25 is detected while M25 is ON.
  • Causes: • Tray lift-up motor /1 (M25) • Printer control board (PRCB) DIPSW18-0
  • Remedy: 1. Check the connector connection and the wiring between PRCB and the motor, and repair it if any abnormality. 2. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram:Main body (3/4): 16-A) 3. Replace M25 4. Replace PRCB.
  • Code: C-0205
  • Description: Tray2 up abnormality 1. When the upper limit sensor /2 (PS10) is OFF, PS10 does not turn ON within 20 seconds after the tray lift-up motor /2 (M34) turns ON for lifting operation. At this time, an error detection signal (24V cut off) is detected.
  • Causes: • Upper limit sensor /2 (PS10) • Tray lift-up motor /2 (M34) • Printer control board (PRCB) • DC power supply /2 (DCPS/2) DIPSW18-1
  • Remedy: 1. Check the paper loaded condition and the rear end restriction plate condition of the tray2, and repair it if any abnormality 2. Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality 3. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram:Main body (3/4): 21-A) 4. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: Main body (2/4): 18-A) 5. Replace PS10. 6. Replace M34 7. Replace PRCB. 8. Replace DCPS /2
  • Code: C-0207
  • Description: Tray /2 up abnormality 2. When the upper limit sensor /2 (PS10) is OFF, PS10 does not turn ON within 20 seconds after the tray lift-up motor /2 (M34) turns ON for lifting operation. At this time, an error detection signal is not detected.
  • Causes: • Upper limit sensor /2 (PS10) • Tray lift-up motor /2 (M34) • Printer control board (PRCB) • DC power supply /2 (DCPS/2) DIPSW18-1
  • Remedy: 1. Check the paper loaded condition and the rear end restriction plate condition of the tray2, and repair it if any abnormality 2. Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality 3. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram:Main body (3/4): 21-A) 4. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: Main body (2/4): 18-A) 5. Replace PS10. 6. Replace M34 7. Replace PRCB. 8. Replace DCPS /2
‹ First  < 4 5 6 7 8 9 10 >  Last ›
Thêm vào giỏ hàng thành công
popup

Số lượng:

Tổng tiền:

Danh mục