• Code: C0880
• Description: Program archive problem (optional fax) When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed.
• Causes: Defective fax software. Defective fax control PWB.
• Remedy: Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation.

• Code: C0890
• Description: Fax control PWB CG FONT archive problem (optional fax) When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed.
• Causes: Defective fax software. Defective fax control PWB.
• Remedy: Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation.

• Code: C0920
• Description: Fax file system error The backup data is not retained for file system abnormality of flash memory of the fax control PWB.
• Causes: Defective fax control PWB.
• Remedy: Defective fax control PWB. Replace the fax control PWB and verify the operation.

• Code: C1010
• Description: Lift motor 1 error When cassette 1 is inserted, lift limit switch 1 does not turn on within 12 s of lift motor 1 turning on.
• Causes: Poor contact in the connector terminals. Broken gears or couplings of lift motor 1. Defective lift motor 1. Defective lift switch 1. Poor contact in the connector terminals. Defective PWB.
• Remedy: Poor contact in the connector terminals. Check the connection of connector of lift motor 1 and the connector YC25 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Broken gears or couplings of lift motor 1. Replace lift motor 1. Defective lift motor 1. Check for continuity across the coil. If none, replace lift motor 1. Defective lift switch 1. Check if YC9-12 on the feed PWB goes low when lift switch 1 is turned off. If not, replace lift switch 1. Poor contact in the connector terminals. Check the connection of connector of lift switch 1 and the connector YC9 on the feed PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Replace the feed PWB or engine PWB and check for correct operation.

• Code: C1020
• Description: Lift motor 2 error When cassette 2 is inserted, lift limit switch 2 does not turn on within 12 s of lift motor 2 turning on.
• Causes: Poor contact in the connector terminals. Broken gears or couplings of lift motor 2. Defective lift motor 2. Defective lift switch 2. Poor contact in the connector terminals. Defective PWB.
• Remedy: Poor contact in the connector terminals. Check the connection of connector of lift motor 2 and the connector YC25 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Broken gears or couplings of lift motor 2. Replace lift motor 2. Defective lift motor 2. Check for continuity across the coil. If none, replace lift motor 2. Defective lift switch 2. Check if YC9-6 on the feed PWB goes low when lift switch 2 is turned off. If not, replace lift switch 2. Poor contact in the connector terminals. Check the connection of connector of lift switch 2 and the connector YC9 on the feed PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Replace the feed PWB or engine PWB and check for correct operation.

• Code: C1030
• Description: Paper feeder lift motor 1 error (optional paper feeder) When optional cassette 3 is inserted, paper feeder lift switch 1 does not turn on within 12 s of paper feeder lift motor 1 turning on. The lift overcurrent protective monitor signal is detected above 500 ms during driving the motor. However, the first 1 s after paper feeder lift motor 1 is turned on is excluded from detection.
• Causes: Poor contact in the connector terminals. Broken gears or couplings of paper feeder lift motor 1. Defective paper feeder lift motor 1. Defective paper feeder lift switch 1.
• Remedy: Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Broken gears or couplings of paper feeder lift motor 1. Replace paper feeder lift motor 1. Defective paper feeder lift motor 1. Check for continuity across the coil. If none, replace paper feeder lift motor 1. Defective paper feeder lift switch 1. Check if YC1-5 on the paper feeder main PWB goes low when paper feeder lift switch 1 is turned off. If not, replace paper feeder lift switch 1.

• Code: C1040
• Description: Paper feeder lift motor 2 error (optional paper feeder) When optional cassette 4 is inserted, paper feeder lift switch 2 does not turn on within 12 s of paper feeder lift motor 2 turning on. The lift overcurrent protective monitor signal is detected above 500 ms during driving the motor. However, the first 1 s after paper feeder lift motor 2 is turned on is excluded from detection.
• Causes: Poor contact in the connector terminals. Broken gears or couplings of paper feeder lift motor 2. Defective paper feeder lift motor 2. Defective paper feeder lift switch 2.
• Remedy: Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Broken gears or couplings of paper feeder lift motor 2. Replace paper feeder lift motor 2. Defective paper feeder lift motor 2. Check for continuity across the coil. If none, replace paper feeder lift motor 2. Defective paper feeder lift switch 2. Check if YC1-7 on the paper feeder main PWB goes low when paper feeder lift switch 2 is turned off. If not, replace paper feeder lift switch 2.

• Code: C1100
• Description: Paper feeder lift motor 1 error (optional 3000-sheet paper feeder) A motor over-current signal is detected continuously for 1 s or longer.
• Causes: Poor contact in the connector terminals. Paper feeder lift motor 1 does not rotate correctly (the motor is overloaded).
• Remedy: Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Paper feeder lift motor 1 does not rotate correctly (the motor is overloaded). Check the gears and remedy if necessary.