Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera KMC3225 — Trang 9/17

Code: C5303

Description: Cleaning lamp M break error After the cleaning lamp M ON signal is turned on, the cleaning lamp M break signal is detected continuously 5 times for 10 ms.
Causes: Poor contact in the connector terminals. Defective cleaning lamp M. Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC17 on the engine PWB and the connector on the drum unit M, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp M. Replace the drum unit M. Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C5304

Description: Cleaning lamp Y break error After the cleaning lamp Y ON signal is turned on, the cleaning lamp Y break signal is detected continuously 5 times for 10 ms.
Causes: Poor contact in the connector terminals. Defective cleaning lamp Y. Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC18 on the engine PWB and the connector on the drum unit Y, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp Y. Replace the drum unit Y. Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C6000

Description: Fuser thermistor 1/3 break error Fuser thermistor 1 detected 40 C/104 F or less during warming up. 40 C/104 F or less is detected between 10 s of continuation during worming up. Fuser thermistor 3 detected 40 C/104 F or less during warming up.
Causes: Defective fuser heater 1/2. Defective fuser thermostat 1. Installation defectiveness on fuser thermistor 1/2. Defective PWB.
Remedy: Defective fuser heater 1/2. Check for continuity across each heater. If none, replace the fuser unit. Defective fuser thermostat 1. Check for continuity across thermostat. If none, remove the cause and replace the fuser unit. Installation defectiveness on fuser thermistor 1/2. Measure the resistance. If it is ∞Ω, replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.

Code: C6010

Description: Abnormally high fuser thermistor temperature The fuser Abnormally high signal is detected for 60 s or more.
Causes: Defective PWB.
Remedy: Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.

Code: C6020

Description: Abnormally high fuser thermistor 1/3 temperature The fuser temperature exceeds 240 C/ 464 F.
Causes: Defective PWB. Installation defectiveness on fuser thermistor 1/3.
Remedy: Defective PWB. Replace the power source PWB or engine PWB and check for correct operation. Installation defectiveness on fuser thermistor 1/3. Measure the resistance. If it is ∞Ω, replace the fuser unit.

Code: C6030

Description: Fuser thermistor 1/3 break error Fuser thermistor 1 detected 40 C/104 F or less during warming up. 40 C/104 F or less is detected between 10 s of continuation during worming up. Fuser thermistor 3 detected 40 C/104 F or less during warming up.
Causes: Defective fuser heater 1/2. Installation defectiveness on fuser thermistor 1/3. Defective PWB.
Remedy: Defective fuser heater 1/2. Check for continuity across each heater. If none, replace the fuser unit. Installation defectiveness on fuser thermistor 1/3. Measure the resistance. If it is ∞Ω, replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.

Code: C6050

Description: Abnormally low fuser thermistor 3 temperature During copying, the temperature at the heat roller lower than 100 C/212 F is detected continuously for 1 s.
Causes: Defective fuser heater 1/2. Defective PWB.
Remedy: Defective fuser heater 1/2. Replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.

Code: C6100

Description: Fuser heater 3 break Fuser thermistor 2 detected less than 100 C/212 F for 120 s during driving. Fuser thermistor 2 deduced less than 150 C/302 F for 300 s during driving. Fuser thermistor 2 deduced less than 100 C/212 F for 5 s during driving.
Causes: Defective fuser heater 3. Defective fuser thermostat 2. Installation defectiveness on fuser thermistor 2. Defective PWB.
Remedy: Defective fuser heater 3. Check for continuity across each heater. If none, replace the fuser unit. Defective fuser thermostat 2. Check for continuity across thermostat. If none, remove the cause and replace the fuser unit. Installation defectiveness on fuser thermistor 2. Measure the resistance. If it is ∞Ω, replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie