Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MP1350 — Trang 10/25

Code: SC505

Description: 5th Tray (LCT Tray 2) Lift Malfunction
One of the following conditions is detected in the 5th tray:
• The LCT 2nd lift sensor is not activated for 10 s after the LCT 2nd tray lift motor turned on.
• Upper limit is not detected within 10 s while the paper tray is lifting during paper feed.
• The LCT 2nd lift sensor is already activated when the LCT 2nd tray is placed in the machine.
Causes: • Poor LCT 2nd tray lift motor connection
• Remaining paper or another obstruction has stopped the tray and motor
• LCT 2nd pick-up solenoid connector is loose
• LCT 2nd pick-up solenoid is blocked by an obstruction

Code: SC506

Description: 6th Tray (LCT Tray 3) Lift Malfunction
One of the following conditions is detected in the 6th tray.
• The LCT 3rd lift sensor is not activated for 20 s after the LCT 3rd tray lift motor turned on.
• Upper limit is not detected within 20 s while the paper tray is lifting during paper feed.
• The LCT 3rd lift sensor is already activated when the LCT 3rd tray is placed in the machine.
Causes: • Poor LCT 3rd tray lift motor connection
• Remaining paper or another obstruction has stopped the tray and motor
• LCT 3rd pick-up solenoid connector is loose
• LCT 3rd pick-up solenoid is blocked by an obstruction

Code: SC507

Description: 7th Tray (Bypass Tray) Lift Mechanism
One of the following conditions is detected in the optional bypass tray.
• The bypass tray lift sensor is not activated for 10 s after the tray lift motor turned on.
• Upper limit is not detected within 10 s while the paper tray is lifting during paper feed.
• The bypass tray lift sensor is already activated paper is placed in the 7th tray.
Causes: • Poor bypass tray lift motor connection
• Remaining paper or another obstruction has stopped the tray and motor
• Bypass tray pick-up solenoid connector is loose
• Bypass tray pick-up solenoid is blocked by an obstruction

Code: SC529

Description: Exit Junction Gate HP Sensor Error
The exit junction gate did not return to its home position.
Causes: • Cycle the machine off/on

Code: SC531

Description: Fusing Motor Lock
A fusing motor lock signal is detected for more than 2 s during operation due to an electrical overload in the motor driver board.
Causes: • Motor driver board defective. Replace motor.

Code: SC541

Description: Fusing Thermister Open
The fusing temperature detected by the thermistor was below 7°C for 15 s.
Causes: • Fusing thermistor defective or out of position
• Poor thermistor terminal connection

Code: SC542

Description: Fusing Temperature Warm-up Error
One of the following occurred:
• B234/B235: Hot roller did not reach target operation temperature within 360 sec. after the machine was powered or 360 sec. minutes after the doors were closed.
• B236: Hot roller did not reach target operation temperature within 465 sec. after the machine was powered or 465 sec. minutes after the doors were closed.
• Fusing temperature rose only 5C toward the fusing temperature within 20 s after the machine was powered on, or after the doors were closed.
• Fusing temperature rose only 5C toward the fusing temperature within 20 s after thermistor started monitoring hot roller temperature. (The thermistors starts monitoring 25 s after the hot roller starts rotating.)
Causes: • Fusing lamp(s) disconnected
• Thermistor out of position

Code: SC543

Description: Fusing Overheat Error 1: Software
A fusing temperature of over 210°C is detected for 5 s by the fusing thermistor. This prevents the fusing lamps from switching on without a fusing lamp trigger signal.
Causes: • AC drive board defective (TRIAC short)
• BCU defective
• BCU firmware defective
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie