Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MP3350 — Trang 6/17

Code: 504

Description: 4th paper tray lift motor malfunction (optional Paper Tray Unit)
The paper lift sensor did not activate within 18 sec. after the tray lift motor switched on.
Causes: • An obstruction (jammed paper, paper scraps, etc.) has blocked the motor drive and caused an overload. • Paper lift sensor connection loose, disconnected, or damaged • Paper lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective

Code: 506

Description: Paper tray motor lock (optional Paper Tray Unit)
A motor lock signal is not detected for more than 1.5 s or the lock signal is not detected for more than 1.0 s during rotation.
Causes: • An obstruction (jammed paper, paper scraps, etc.) has blocked the motor drive and caused an overload. • Paper tray motor connection loose, disconnected, or damaged • Paper tray motor defective

Code: 508

Description: LCT rear fence drive error
The return position sensor is not activated after the rear fence drive motor has been on to lower the tandem tray for 8 seconds.
Causes: • An obstruction (jammed paper, paper scraps, etc.) has jammed the rear fence or motor • Rear fence motor connection loose, disconnected, or damaged • Rear fence motor defective • Return position sensor connector loose, disconnected, or damaged • Return position sensor defective

Code: 509

Description: LCT side fence drive error
The side fence positioning sensor is not activated for more 3 seconds when the paper stack in the left tray is moved to the right tray. The side fence close sensor is not activated for more 3 seconds after moving the paper stack to the right tray.
Causes: • An obstruction (jammed paper, paper scraps, etc.) has jammed the rear fence or motor • Side fence motor disconnected or defective • Side fence position sensor disconnected or defective Side fence close sensor disconnected or defective

Code: 510

Description: LCT lower limit error
The lower limit sensor does not activate within 8 seconds after the tray has been lowered.
Causes: • An obstruction (jammed paper, paper scraps, etc.) has jammed the tray lift motor • Tray lift motor defective • Poor connection of the tray lift motor • Lower limit sensor disconnected or defective Obstruction that causes overload on the drive mechanism.

Code: 541

Description: Fusing thermistor open (center)
The temperature of the hot roller remained below 0C for 5 sec at the center of the hot roller.
Causes: • Fusing thermistor out of its position because of incorrect installation • Fusing thermistor disconnected or defective • Power supply not within rated range (15% or more below rating)

Code: 542

Description: Fusing temperature warm-up error (center)
The fusing temperature did not reach the standby temperature within 20 sec. at the center of the hot roller after the main switch turned on.
Causes: • Fusing thermistor defective or out of position • Fusing lamp disconnected • Thermistor defective • Fusing lamp defective

Code: 543

Description: Fusing overheat error 1 (center)
The fusing thermistor detected a fusing temperature over 230 °C for 5 sec. at the center of the hot roller.
Causes: • TRIAC short on PSU (PSU defective) • BCU board defective • Fusing thermistor defective
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie