Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MP7001 — Trang 8/28

Code: 495

Description: Toner recycling unit error
Encoder pulse does not change for 3 s after the main motor switches on.
Causes: • Waste toner transport has stopped due to motor overload • Toner end sensor detective, disconnected
Remedy:

Code: 496

Description: Toner collection bottle error
The toner collection bottle set switch remains off when the front door is closed.
Causes: • No toner collection bottle set • Poor connection of the switch connector
Remedy:

Code: 497

Description: Toner collection motor error
The toner collection motor connector set signal remains off for 1 s.
Causes: • Toner pump motor defective • Motor connector loose, disconnected
Remedy:

Code: 501

Description: Tray 1 lift malfunction
• The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 s. • Tray overload detected when the tray is set. • The lower limit sensor of the LCT does not detect the lower limit within 10 s.
Causes: • Tray lift motor defective, disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected, blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray. • This SC will not display until the operator has pulled the tray out and pushed it in 3 times. • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.
Remedy:

Code: 502

Description: Tray 2 lift malfunction
• The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 s. • Tray overload detected when the tray is set.
Causes: • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray. • This SC will not display until the operator has pulled the tray out and pushed it in 3 times. • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.
Remedy:

Code: 503

Description: Tray 3 lift malfunction
• The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 s. • Tray overload detected when the tray is set.
Causes: • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray. • This SC will not display until the operator has pulled the tray out and pushed it in 3 times. • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.
Remedy:

Code: 504

Description: Tray 4 lift malfunction
• The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 s. • Tray overload detected when the tray is set.
Causes: • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray. • This SC will not display until the operator has pulled the tray out and pushed it in 3 times. • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.
Remedy:

Code: 507

Description: LCT feed motor malfunction
One of the following conditions is detected: • The LD signal from the feed motor is detected abnormal for 50 ms after the motor switches on. • At power on, the motor is detected loose or disconnected.
Causes: • Feed motor defective • Feed motor connector disconnected • Obstacle interfering with mechanical movement of motor
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie