• Code: SC792-1
• Description: Junction gate error
  Detected at HP after the time prescribed to leave the HP had elapsed (more than 36 pulses) (1 detection, jam, twice detected, SC error) -or- Not detected at HP after the time prescribed to arrive at the HP had elapsed (more than 22 pulses) (1 detection, jam, twice detected, SC error)
• Causes: • Path JG motor (M201) defective • Motor connector loose, broken, defective • Motor overload • Path JG sensor (S203) connector loose, broken, defective • Sensor (S203) defective

• Code: SC792-10
• Description: Binder unit runout error
  Not detected at HP after the time prescribed to arrive at the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error) -or- Detected at HP after the time prescribed to leave the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error)
• Causes: • Runout press roller motor (M610) connector loose, broken, defective • Motor defective • Motor overload • Runout roller HP sensor (S614) connector loose, broken, defective • Sensor defective

• Code: SC792-11
• Description: Clamp thickness error 50-sheet detection sensor (S606) went OFF during pre-bind jogging when a 100- sheet thickness was detected. (1st detection jam, 2nd detection SC error) -or- 50-sheet detection sensor went OFF at initialization when the clamp moved to the open position.
• Causes: • 50-sheet detection sensor (S606) connector loose, broken, defective • Sensor defective

• Code: SC792-12
• Description: Alignment pin error
  Not detected at HP after the time prescribed to arrive at the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error) -or- Detected at HP after the time prescribed to leave the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error)
• Causes: • Alignment pin motor (M602) connector loose, broken, defective • Motor overload • Motor defective • Alignment pin HP sensor (S604) connector loose, broken, defective • Sensor defective

• Code: SC792-13
• Description: Pre-bind jogger shutter error
  Not detected at HP after the time prescribed to arrive at the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error) -or- Detected at HP after the time prescribed to leave the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error)
• Causes: • Shutter motor (M608) connector loose, broken, defective • Motor overload • Motor defective • Shutter HP sensor (S605) connector loose, broken, defective • Sensor defective

• Code: SC792-15
• Description: Timing sensor interval error
  The bind timing sensor (S702) remained ON or OFF longer than the prescribed time (1500 ms) during initialization or ring binding (1st detection: jam, 2nd detection: SC error)
• Causes: • Clamp unit motor (M701) connector loose, broken, defective • Motor overload • Motor defective • Bind timing sensor (S702) connector loose, broken, defective • Sensor defective

• Code: SC792-16
• Description: Clamp unit HP error
  At initialization or during ring binding, did not arrive at the home position within the prescribed time (1500 ms) (1st detection: jam, 2nd detection: SC error) -or- Detected at HP after the time prescribed to leave the HP had elapsed (more than 1500 ms) (1st detection, jam, 2nd detection, SC error)
• Causes: • Clamp unit motor (M701) connector loose, broken, defective • Motor overload • Motor defective • Clamp unit HP sensor (S701) connector loose, broken, defective • Sensor defective

• Code: SC792-17
• Description: Spine alignment error
  During pin alignment operation, the pin did not reach the up position or return to the home position with the prescribed time (400 ms), and one retry failed within the same time limit.
• Causes: • Alignment pin motor (M602) connector loose, broken, defective • Motor overload • Motor defective • Alignment pin HP sensor (S604) connector loose, broken, defective, or sensor defective • Alignment pin up sensor (S610) connector loose, broken, defective, or sensor defective • Stack not jogged correctly, or not punched correctly