• Code: SC725-32
• Description: 3rd Stopper Motor Erro (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
• Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
• Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.

• Code: SC725-33
• Description: Jogger Fence Motor Error (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
• Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
• Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.

• Code: SC725-34
• Description: Dynamic Roller Lift Motor Error (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
• Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
• Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.

• Code: SC725-35
• Description: Registration Roller Release Motor Error (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
• Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
• Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.

• Code: SC725-36
• Description: FM2 Direct-Send JG Motor Error (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
• Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
• Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.

• Code: SC725-37
• Description: FM6 Pawl Motor Error (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
• Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
• Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.

• Code: SC725-38
• Description: Fold Plate Motor Error (D615) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • Motor driver detected an error. (SC from the first time)
• Causes: • Overcurrent to the motor. • Motor drive overheat • Connector disconnected
• Remedy: • Replace the controller board. • Replace the motor. • Replace the harness. • Re-connect the connector. • Replace the sensor.

• Code: SC725-39
• Description: 1st Fold Motor Error (D615) • Motor driver detected an error. (SC from the first time)
• Causes: • Overcurrent to the motor. • Motor drive overheat
• Remedy: • Replace the controller board. • Replace the motor. • Replace the harness.