Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh B234 MP9000 B-C3 — Trang 16/25

Code: SC738

Description: Pre-Stack Junction Gate Release Motor Error: 3K Finisher B830
The pre-stack junction gate release HP sensor did not detect the gate at the home position within 200 ms after two attempts. -or- The HP sensor twice detected the gate at the home position for more than 200 ms after it was supposed to open.
Causes: • Junction gate did not arrive at the home position within the specified time
• Junction gate did not leave the home position within the specified time

Code: SC740

Description: Finisher Corner Stapler Motor Error: 3K Finisher B830
The stapler motor did not switch off within 600 ms after operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: • Number of sheets in the stack exceeded the limit for stapling
• If error occurred during stapling, stapler rotation sensor 1 defective (replace stapler)
• If error did not occur during stapling: staple jam:
1 Motor blocked by an obstruction
2 Stapler motor harness loose, broken, defective
3 Corner stapler motor defective
4 Main control board defective

Code: SC741

Description: Finisher Corner Stapler Rotation Motor Error: 3K Finisher B830
The stapler did not return to its home position within the specified time after stapling. -or- The stapler failed to leave the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: • If the motor is running, 1 Stapler rotation home position sensor harnesses are broken, loose, or defective 2 Stapler rotation home position sensors are defective
• If the motor is not running: 1 Motor is blocked by an obstruction 2 Motor harness is loose, broken, defective 3 Motor is defective

Code: SC742

Description: Finisher Stapler Movement Motor Error: 3K Finisher B830
The stapler did not return to its home position within the specified time after stapling. -or- The stapler failed to leave the home position within the specified time The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: • If the motor is running, 1 Stapler home position sensor harness is broken, loose, or defective 2 Stapler home position sensor is defective
• If the motor is not running: 1 Motor is blocked by an obstruction 2 Motor harness is loose, broken, defective 3 Motor is defective

Code: SC743

Description: Booklet Stapler Motor Error 1: Front Motor (Booklet Finisher)
The front stapler unit saddle-stitch motor does not start operation within 600 ms. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: • Front motor harness loose, broken, defective
• Front motor overloaded due to obstruction
• Front motor defective
• Booklet finisher control board defective

Code: SC744

Description: Booklet Stapler Motor Error 2: Rear Motor (Booklet Finisher)
The rear stapler unit saddle-stitch motor does not start operation within 500 ms. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: • Rear motor harness loose, broken, defective
• Rear motor overloaded due to obstruction
• Rear motor defective
• Booklet finisher control board defective

Code: SC745

Description: Feed-Out Belt Motor Error (Booklet Finisher)
The stack feed-out belt HP sensor does not activate within the specified time after the stack feed-out belt motor turns on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: • If the motor is operating 1 Stack feed-out HP sensor harness loose, broken, defective 2 Stack feed-out HP sensor defective
• If the motor is not operating: 1 Feed-out motor blocked by an obstruction 2 Feed-out motor harness loose, broken, defective 3 Feed-out motor defective 4 Booklet finisher main board defective

Code: SC746

Description: Stack Plate Motor Error 1: Front Motor (3K Finisher B830)
The stack plate HP sensor (front) does not activate within 500 ms after the motor turns on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: • If the motor is operating 1 Front stack plate HP sensor harness loose, broken, defective 2 Front stack plate HP sensor defective
• If the motor is not operating: 1 Motor blocked by an obstruction 2 Motor harness loose, broken, defective 3 Motor defective 4 Booklet finisher main board defective
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie