Description: Clamp Roller Retraction Motor
The clamp roller did not return to the home position within the specified time.
Causes: • Clamp roller mechanism overloaded due to an obstruction
• Clamp roller HP sensor connector loose, broken, defective
• Clamp roller HP sensor defective
• Clamp roller retraction motor connector loose, broken, defective
• Clamp roller retraction motor defective
• Main control board defective
Description: Cover Interposer Lift Motor 1 Error
In the first tray:
• The upper limit sensor did not detect the bottom plate within the specified time after the lift motor switched on to lift the bottom plate.
• The lower limit sensor did not direct the bottom plate within the specified time after the lift motor switched on to lower the bottom plate.
Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code.
Description: Cover Interposer Lift Motor 2 Error
In the second tray:
• The upper limit sensor did not detect the bottom plate within the specified time after the lift motor switched on to lift the bottom plate.
• The lower limit sensor did not direct the bottom plate within the specified time after the lift motor switched on to lower the bottom plate.
Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code.
Description: Cover Interposer Pickup Motor 1 Error
In the first tray:
• While the pick-up roller motor was on, the pick-up roller HP sensor did not detect the pick-up roller at the home position within the specified number of pulses.
• While the pick-up roller motor was on, the pick-up roller HP sensor did not detect the pick-up roller at the home position above the specified number of pulses.
Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code.
Causes: • The pick-up motor, pick-up roller HP sensor harnesses, connectors were loose, broken, defective
• Pick-up motor overload due to an obstruction
• Pick-up motor defective
• Pick-up roller HP sensor defective
Description: Cover Interposer Pickup Motor 2 Error
In the second tray:
• While the pick-up roller motor was on, the pick-up roller HP sensor did not detect the pick-up roller at the home position within the specified number of pulses.
• While the pick-up roller motor was on, the pick-up roller HP sensor did not detect the pick-up roller at the home position above the specified number of pulses.
Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code.
Causes: • The pick-up motor, pick-up roller HP sensor harnesses, connectors were loose, broken, defective
• Pick-up motor overload due to an obstruction
• Pick-up motor defective
• Pick-up roller HP sensor defective
Description: Jogger Top Fence Motor: 3K Finisher B830
The top fence HP sensor detected that: The top fence did not arrive at the home position within the specified number of pulses. -or- The top fence failed to leave the home position within the specified number of pulses.
Causes: • If the jogger top fence motor is operating: 1 Top fence HP sensor harness loose, broken, defective 2 Top fence HP sensor defective
• If the jogger top fence motor is not operating: 1 Motor blocked by an obstruction 2 Motor harness loose, broken, defective 3 Motor defective 4 Finisher main board defective
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.