Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh G148 SP9100DN MT-P2 — Trang 13/18

Code: 790

Description: Finisher staple trimming hopper full
The staple waste hopper is full of cut staples.
Causes: • If the hopper is full, empty the hopper • If the hopper is not full, the hopper full sensor is disconnected, defective

Code: 817

Description: Monitor Error
This is a file detection and electronic file signature check error when the boot loader attempts to read the self-diagnostic module, system kernel, or root system files from the OS Flash ROM, or the items on the SD card in the controller slot are false or corrupted.
Causes: • OS Flash ROM data defective; change the controller firmware • SD card data defective; use another SD card

Code: 818

Description: Watchdog error
While the system program is running, a bus hold or interrupt program goes into an endless loop, preventing any other programs from executing.
Causes: • System program defective; switch off/on, or change the controller firmware if the problem cannot be solved • Controller board defective • Controller option malfunction

Code: 819

Description: Fatal kernel error
Due to a control error, a RAM overflow occurred during system processing. One of the following messages was displayed on the operation panel.
Causes: • System program defective • Controller board defective • Optional board defective • Replace controller firmwarelayed

Code: 821

Description: Self-diagnostic error: ASIC
The Write & Verify check of the ASIC returned an error. Note: The main ASIC module on the controller board controls the bus of the ROM device.
Causes: • Replace the controller board

Code: 822

Description: Self-diagnostic error: HDD
Causes: 3003 Check performed when HDD is installed: • HDD device busy for over 31 s. • After a diagnostic command is set for Sthe HDD, but the device remains busy for over 6 s. A diagnostic command is issued to the HDD device but the result is an error • HDD defective • HDD harness disconnected, defective • Controller board defective 3004 No response to the self-diagnostic command from the ASIC to the HDDs • HDD defective 3013 Mandolin does not respond, the HDD device remains BUSY for more than 31 s, or the BUSY signal does not drop within 6 s after the diagnostic command is issued to the HDDs. • HDD defective • HDD connector loose or defective • Controller defective 3014 Error returned from HDD in response to the self-diagnostic command, Mandolin could not be located due to a read/write error at the HDD register. • HDD defective

Code: 824

Description: Self-diagnostic error 4: NVRAM
One or more of the following conditions exist: • NVRAM not present. • NVRAM damaged • NVRAM socket damaged
Causes: • NVRAM defective • Controller board defective • NVRAM backup battery exhausted • NVRAM socket damaged Note: In every case, the controller board must be replaced.

Code: 826

Description: Self-diagnostic error 6: NVRAM (option NVRAM)
Causes: 1501 The difference between the 1 s measured for RTC in the NVRAM and the 1 s timeout of the CPU is out of range, or the NVRAM is not detected. • NVRAM defective • NVRAM installed incorrectly 15FE Backup battery error. Battery is exhausted or not within rated specification. • The battery is attached permanently to the controller board. Replace the controller board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie